From the Loftsmith Workshop
Self-tapping screw boss test: pilot hole x boss wall, M2-M4
Stop guessing how big to drill the hole for a screw in your own printed parts. Print this little plate, drive a screw into each post, and see which hole and wall thickness grips best. Orange numbers mark every size, and you can change the smallest and largest pilot sizes.
1 part · 16 g · 90 × 59 × 9 mm
Remix of Heat-set insert tester
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- boss-test · PLA (or whatever filament you build encl · Flat on the bed with the bosses pointing up (default). With the horizontal option it stands on the edge under the pilot-hole labels so the bosses lie on their side. No supports either way.
At the defaults: 90.4 x 58.6 x 9 mm, 20 M3 bosses 9 mm tall with a 0.4 mm top chamfer, a 0.4 mm pilot lead-in and a 1 mm root fillet. Pilots 2.1/2.25/2.4/2.55/2.7 mm, boss ODs 5.4/6.2/7.0/7.8 mm, walls 1.35-2.85 mm. The pilot holes go right through.
- labels · PLA in a contrasting colour (filament sl · Printed in place on top of the plate as part of the same object (vertical option only)
Raised 0.6 mm, 5 mm bold labels: pilot sizes along the front, boss ODs down the right edge, screw size in the front-right corner. Only the top 0.6 mm changes colour. Without a second filament, assign both to one slot and the labels stay readable as raised text. In the horizontal option they are part
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 walls for the stats shown; better to use the same wall count you print enclosures with, because that decides whether a boss is solid or has infill
- Infill
- 15% for the stats shown; match your enclosure settings
- Supports
- None
- Notes
- Default (vertical, M3, labels in a second filament): about 19 g and 32 min at 2 walls/15%, including about 2.6 g and 6 min for the 4 colour changes. About 23 g and 39 min at 3 walls/15%. Use the same nozzle, temperature and filament as your real parts.
Hardware
- 20 × M3 x 8 mm screws (thread-forming for plastic, or the machine screws you actually use) · One per boss at the defaults. The length follows the Screw size and Engagement sliders and is shown in the Screw engagement check (for example #6 x 10 at the default engagement). Fewer screws are fine
Assembly
- Print the plate in the filament and with the wall count you use for enclosures.
- Drive one screw into each boss by hand until the head seats on top. The 0.4 mm lead-in at each hole mouth helps the screw start straight. Use the same screwdriver and about the same force you would on a real part.
- Note each cell: split (the boss cracks along its length), stripped (the screw spins and will not tighten) or good (it tightens firmly and the boss stays whole).
- Pick the smallest pilot that does not split the boss, then the thinnest boss in that column that stays whole. Read the pilot size off the front labels and the boss OD off the right-hand labels.
- Use that pilot hole and boss OD in your enclosure design. Run the test again in the horizontal orientation if your bosses print sideways.
Good to know
- Checked in the Loftsmith engine only. It has not been printed, and no screws have been driven into it yet.
- Printed holes usually come out a little smaller than modelled. The labels show the modelled size, which is the number you type into your CAD.
- The result only applies to the filament, wall count, infill and temperature you print the test with. A boss that holds in PETG can split in PLA.
- It shows splitting and stripping during installation. It does not measure pull-out force, creep under long-term load, or how many times a screw can be removed and refitted.
- Horizontal bosses have a keel underneath and a flat-topped roof in each pilot hole so they print without support. They are a bit stronger at the keel than a perfectly round boss.
- The screw length is rounded up to a standard size, so real engagement can be above the slider value. Screws longer than the boss height will poke out of the bottom.
Comments