From the Loftsmith Workshop
Painter's pole vacuum adapter, tilt head, 30-40 mm wands
Lets you hook a vacuum onto the end of a painter's pole, so dust gets sucked up where you sand instead of drifting down on you. The head tilts and locks with a knurled knob, and a small strap clip holds the hose against the pole. Change the wand and pole sizes to match yours.
4 parts · 56 g · 88 × 75 × 215 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- coupler · PETG · Upright, threaded (open) end on the bed
41 x 31 x 81 mm, about 17 g, 33 min at 2 walls/15%. Female 3/4"-5 ACME thread, 24 mm long. The Clamp option instead has a 30 mm deep bore and a side lobe for an M5 thumb screw. PETG so the thread and teeth wear well. The internal thread flanks are the only overhangs the engine flags. Print them with
- head · PETG · Standing on the socket end, tube vertical (the slicer drops it upright from the 45 degree display pose)
41 x 57 x 88 mm, about 31 g, 52 min at 2 walls/15%, no supports. Has the tapered socket for the hose wand, the tapered spigot for the tool, 24 face teeth and a nut slot on top.
- knob · PETG · Flat face down
32 mm fluted knob, about 3 g, 9 min. The M6 bolt head presses into its hex pocket.
- hose clip · PETG · Flat
Figure-eight snap clip for the pole and hose, about 5 g, 12 min. PETG flexes without cracking.
Print settings
- Layer height
- 0.2 mm
- Walls
- 3 recommended (the page stats use 2)
- Infill
- 15%
- Supports
- Off. The only faces the engine flags are the flanks of the coupler's internal ACME thread: about 505 of the 530 mm² it reports, or up to about 2 g if a slicer supported them. They are short ledges about 1.7 mm deep. Print them without supports, because support inside a thread can't be removed. The h
- Notes
- All parts in PETG for thread wear, the snap clip and a little heat tolerance. The engine estimates about 58 g and 1 h 50 min for all four parts at 2 walls/15%, or about 78 g and 2 h 28 min at the recommended 3 walls/15%. If the pole thread runs tight, raise the Pole thread clearance slider (0.15-0.5
Hardware
- M6 x 30 hex bolt (ISO 4017, fully threaded) · Head pressed into the knob; it clamps the tooth joint.
- M6 hex nut · Drops into the slot on top of the head.
- M5 x 16 thumb screw and M5 hex nut · Clamp option only, for plain 22-32 mm poles.
Assembly
- Drop the M6 nut into the slot on top of the head and push it down until it lines up with the bolt hole.
- Press the M6 x 30 hex bolt head into the hex pocket on the flat face of the knob.
- Push the bolt through the coupler's lug from the knob side, mesh the head's teeth at the angle you want, and thread the bolt into the nut. Tighten the knob firmly by hand.
- Screw the coupler onto the pole's threaded tip. If it is stiff, run it on and off a few times. For the Clamp option, push an M5 nut up into the slot from below, slide the coupler onto the pole and tighten the thumb screw.
- Push the hose wand end up into the socket at the bottom of the head, and push the tool's cuff onto the spigot at the top. Use the Fit adjust slider if either is loose or will not go on.
- Snap the clip onto the pole lower down and snap the hose into its other ring.
- To change the angle, back the knob off two or three turns, pull the head out about 2.5 mm until the teeth clear, turn it to the next 15-degree step and retighten.
Good to know
- Checked in the Loftsmith engine only, not printed or tested. Fits, thread engagement and clamp forces are estimates.
- The thread is 3/4"-5 ACME, the usual US painter's pole tip. Many European poles use other threads. Use the Clamp option for those and for plain 22-32 mm poles.
- If the thread is tight on your pole, raise the Pole thread clearance slider and reprint the coupler, or run it on and off a few times.
- Sized for a tool and wand end up to about 0.5 kg. It is not meant to carry a whole stick vacuum body on the pole.
- Measure your wand's outside diameter yourself (32 and 35 mm are common) and set the slider. The tool must have a cuff that fits that same size.
- The angle holds only when the knob is tight. A loose knob lets the teeth ride over.
- Vacuuming textured or popcorn ceilings can knock material off. Test a small area first.
Comments