From the Loftsmith Workshop
Cookie press discs: wreath, star, tree, snowflake 40-75 mm
Spare discs for a cookie press, so the dough comes out as a wreath, star, tree or snowflake. Each disc sits inside a thin fit ring, which keeps it snug in the barrel. Measure one of your original discs and match the diameter.
4 parts · 10 g · 118 × 57 × 8 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- disc · PETG · As modeled: cookie face (flat, chamfered, fully open) down on a smooth plate, plunger side up
About 4 g and 10 minutes at the page's 2 walls/15% setting; print it at 100% infill. PETG takes warm washing water better than PLA. At the defaults the wreath centre is held by 5 bridges on the plunger side that start 0.6 mm above the bed and print as short bridges.
- fit-ring-minus · PETG · Flat
Measured diameter -0.2 mm, marked with 1 notch on the inner edge. About 2 g, 6 minutes.
- fit-ring-nominal · PETG · Flat
Measured diameter, marked with 2 notches. About 2 g, 6 minutes.
- fit-ring-plus · PETG · Flat
Measured diameter +0.2 mm, marked with 3 notches. About 2 g, 6 minutes.
Print settings
- Layer height
- 0.2 mm (0.12-0.16 mm gives a smoother cookie face)
- Walls
- 2 (the page figures); the disc is only 2.4 mm thick, so it prints mostly solid anyway
- Infill
- 100% for the disc, because the strength check assumes a solid plate; the rings can use any infill
- Supports
- None. Every part prints flat.
- Notes
- Build report at 2 walls/15% for the default disc and three rings: about 10 g of PETG and 29 minutes. The disc alone is about 4 g and 10 minutes, and each ring about 2 g and 6 minutes. The report has no figure for 100% infill; expect the disc to weigh a little more than 4 g. Use a smooth plate so the
Assembly
- Measure one of your existing discs across with calipers and enter it as Disc diameter; do the same for Disc thickness.
- Print the three fit rings, about 6 minutes each. Drop each one into your press's end cap where a disc sits. The notches on the inner edge mark the size: 1 notch is -0.2 mm, 2 notches is your measurement, 3 notches is +0.2 mm.
- Pick the ring that drops in with no visible gap and no forcing, then set Fit adjust to the same value (-0.2, 0 or +0.2). If even the 1-notch ring is tight, or the 3-notch ring is loose, re-measure your disc, change Disc diameter and print the rings again.
- Measure how far the cap's inward lip covers the disc edge, then set Plain band at the edge to that width plus 1.5 mm so no opening hides under the lip.
- Choose the shape, shape size, number of openings and the rim, then print the disc cookie face down at 100% infill.
- Wash the disc by hand. Put it in the cap with the cookie face (flat, chamfered, fully open) pointing out toward the baking sheet and the plunger side (bridges and optional rim) facing into the barrel, then screw the cap on.
Good to know
- Not certified food-safe. Layer lines can hold dough and butter, so wash by hand in warm (not hot) water, dry the disc fully, and reprint one that gets scratched or stained.
- Presses differ, even within one brand, so print the fit rings before the disc. The engine models the cap seat only as your measured diameter plus 0.4 mm and can't model your real cap or its lip; the only real fit test is the rings in your press.
- The strength checks assume a 100 N push on the plunger. Very cold, stiff dough or forcing a jammed press can exceed that. Discs thinner than 2.2 mm are not offered because they would go over PETG's allowable stress.
- Shape size is capped automatically so the openings keep 1.5 mm of plastic between them and the edge band, and the cap shrinks as you add openings. The build log lists the cap for 1, 2 and 3 openings at your settings.
- Dough has to close up behind the wreath's recessed bridges, as it does with commercial wreath discs. That isn't verified here and depends on your dough.
- Hand wash only. PETG softens at around 75 °C, so a dishwasher may warp the disc.
Comments