From the Loftsmith Workshop

Watch travel case for 1-3 watches, sized to your wrist

Keeps your watches from knocking together in a bag. Each one sits in its own rounded pocket with the strap curled around a cushion, and the hinged lid shuts over the top. Set how many watches, and their case size and strap width, to match yours.

4 parts · 119 g · 106 × 173 × 44 mm

by Loftsmith Workshop

Ribbed grey hinged case, open, with two tan watch rolls sitting in separate pockets
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • case · PETG · Upright, bays open to the top; prints as one object with the lid (print group 'case')

    106 x 88 x 32 mm at the defaults, about 48 g and 69 min. Carries the hinge pin and the latch ridge. PETG because the latch tab has to flex every time you open the case, and PETG is tougher than PLA when it bends.

  • lid · PETG · Printed open: top face down on the bed behind the case, already threaded on the hinge pin; the latch tab stands up from it

    About 35 g and 53 min at the defaults. The 34 mm tab tapers from 20 to 9 mm wide and is 1.6 mm thick.

  • pillow ×2 · PETG · Standing on its closed end (open end up)

    One per watch (the quantity follows the Number of watches slider). A hollow stadium cup with 1.6 mm walls, about 18 g and 31 min each at the defaults. Its girth is your wrist size minus 6 mm.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
At the defaults (two watches) everything comes to about 123 g and 3 h 9 min at 2 walls / 15% infill: case + lid 83 g, 2 h 2 min as one object, and each pillow 18 g, 31 min. With 3 walls / 15% it is about 152 g and 3 h 52 min. Export as 3MF so the case and lid stay one object with the hinge gaps kept

Assembly

  1. Print the case and lid together as one object (they come off the bed already hinged), then print one pillow per watch.
  2. Free the hinge: hold the case and work the lid slowly through its full swing a few times until it turns freely.
  3. Buckle each strap on the hole you normally wear. Slide the strap loop over the pillow with the watch head on the flat top, then set the pillow in its bay with the crown towards the wider side of the bay (on the right as you face the latch). The strap under the pillow sits in the channel in the bay f
  4. Close the lid and press it down over the front until the tab's hook clicks under the ridge.
  5. To open, pull the lip at the bottom of the tab towards you with a thumbnail and lift the lid. To take a watch out, lift the pillow and watch out together and slide the strap off the end of the pillow.

Good to know

  • It keeps watches apart and stops them sliding around. It is not padded and not drop-proof, so don't rely on it to protect watches from a hard fall.
  • The pillow is rigid and sized for straps that bend around a 15 mm radius (leather, fabric, rubber). Stiff metal bracelets and some folding clasps may not fit around it.
  • The pillow's girth is your wrist size minus 6 mm. If your strap sits loose or tight on the wrist, measure the inside of the buckled strap and use that for the Wrist slider.
  • The bay allows a fixed 4.5 mm for the crown and assumes 3.5 mm thick straps. A watch thicker than the Thickest watch slider, or with a bigger crown guard, will not let the lid shut.
  • The latch tab prints standing up, so it flexes across its layers. The engine estimate is 4.9 MPa against PETG's 5 MPa across-layer allowable. It needs a firm but gentle pull to open. Don't print it in PLA, and don't bend the tab further than it needs to open.
  • The hook and the ridge each have a 1.6 mm flat ledge that prints without support. Expect a little droop there, which you can clean up with a file if the latch feels gritty.
  • Print-in-place hinges depend on your printer: if the lid is fused, reprint with the Hinge gap slider at 0.45-0.5 mm.
  • Fit, hinge clearance and latch strength were checked in the Loftsmith engine, not on a real print.

Comments