From the Loftsmith Workshop

2.2 in e-paper price tag frame with stand and magnets

Gives a little 2.2 in e-paper price tag a proper place on the shelf or counter. The tag sits behind a rounded frame with a window cut out for the display, and the frame rests on a small leaning stand. Change the tag size and the window to match your own tag.

2 parts · 30 g · 86 × 54 × 61 mm

by Loftsmith Workshop

Dark rounded rectangular frame with a window, resting on a small beige wedge stand
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • frame · PLA · Face down: the front with the bevelled window on the bed, back lips on top (the export applies this rotation).

    85.5 x 55.8 x 17.1 mm, about 18 g and 30 min at 2 walls and 15% infill. PLA works because the snap finger bends only 0.96% when you fit or release the tag, well under PLA's limit, and nothing here gets warm. No supports.

  • stand · PLA · On its side: the wedge profile flat on the bed, so the angled groove prints as vertical walls.

    51 x 53.7 x 19.7 mm, about 12 g and 24 min at 2 walls and 15% infill. No supports.

Print settings

Layer height
0.2 mm
Walls
2 walls (default); 3 walls if you want a stiffer snap finger
Infill
15%
Supports
None
Notes
At 2 walls and 15% infill the whole set is about 31 g and 56 min (frame about 18 g and 30 min, stand about 12 g and 24 min). At 3 walls and 15% it is about 42 g and 1 h 14 min. The frame prints face down. Its back lips are short ledges of up to 2.4 mm and print without support.

Hardware

  • 3 × Neodymium disc magnet 6 x 3 mm · Optional, for fridge use. Pockets are 6.2 mm wide and 3.2 mm deep and open at the back. Glue the magnets in flush.
  • CA glue or 2-part epoxy · A drop per magnet pocket.

Assembly

  1. Measure your tag before you print. The defaults fit the Solum EL022H3 (67.1 x 37.4 x 13.1 mm, display 48.1 x 26.0 mm). For another model, set Tag length, height and thickness, and use Display offset if the screen is not centred on the tag.
  2. Print the frame face down and the stand on its side. Neither needs supports.
  3. Optional: mark one face of each 6 x 3 mm magnet so all three face the same way, then glue them flush into the three back pockets. Let the glue cure.
  4. Slide the tag in from the open right-hand end with its display facing the window. The ramp on the hook pushes the bottom-right finger down, and the finger springs back behind the tag's end.
  5. Set the bottom edge of the frame into the groove of the stand. It leans back at the set angle (18 degrees by default). For the fridge, lift the frame straight up out of the groove.
  6. To take the tag out, put a fingertip into the open right-hand end and press the hook at the bottom down about 2.5 mm. Then push the tag out to the right through the open back.

Good to know

  • Tag sizes come from the OpenEPaperLink wiki and FCC filings, and models differ. Measure your own tag. The display is assumed to sit centred on the tag, so use the offset slider if yours does not.
  • The pocket has 1.2 mm rounded inside edges and assumes the tag's edges are rounded at least that much. A tag with sharp square edges needs a little more fit clearance.
  • The snap finger is PLA and is meant for occasional battery changes, not daily swapping. Fits and the snap feel were checked in the Loftsmith engine, not on a printed part, so try the clearance on your printer first.
  • Fridge hold assumes about 4 N per magnet through the paint and a tag of up to 45 g. Weak or thin magnets, or a textured fridge door, may not hold it.
  • The stand is for a desk or shelf. It needs a 40 degree tilt to tip, but it is not fixed down and is not made for anything other than this frame.
  • No shelf-edge clip is included.

Comments