From the Loftsmith Workshop
Weight-closing squirrel-resistant soda bottle bird feeder
Feeds the birds and gives squirrels nothing for their trouble. A soda bottle sits upside down on a round base with seed ports and a perch ring. Heavier visitors tip the weights and the ports close. Change the port size for small seed or sunflower.
4 parts · 87 g · 138 × 111 × 81 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- collar · PETG · As it hangs: chamber floor on the bed, bottle socket up
About 41 g, 63 min at 2 walls/15%. Internal PCO 1881 thread, 3 seed ports over a 50 degree diverter cone, two pivot fins with stop teeth, two hanger eyes on the roof. No supports.
- sleeve · PETG · Perch ring down on the bed
Print at 100% infill (about 58 g by solid volume) so its weight matches the trigger figure; at 2 walls/15% it is about 37 g, 56 min, and the real trigger moves away from the calculated one. Port windows, two fin slots and two lever ears with 45 degree undersides.
- lever-a · PETG · Lying flat on its outer face; pivot hole vertical
Print at 100% infill (about 8 g by solid volume); about 5 g, 10 min at 2 walls/15%. Chamfered nut post hangs from the long arm, zip-tie holes under the stack.
- lever-b · PETG · Lying flat on its outer face; pivot hole vertical
Same as lever-a, on the opposite fin.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 walls for the collar; sleeve and levers solid (100% infill)
- Infill
- 15% for the collar, 100% for the sleeve and both levers
- Supports
- None
- Notes
- PETG for outdoor use. At these settings the estimate is about 116 g (collar 41 g at 2 walls/15%, sleeve 58 g and levers 8 g each from their solid volumes); the engine gives no print time for this mix. The page's stats line (about 90 g, 2 h 25 min) is for every part at 2 walls/15%, which makes the sl
Hardware
- 10 × M10 hex nuts (DIN 934 / ISO 4032, 17 mm across flats, 8 mm thick) · Counterweight: 5 per lever at the default 320 g trigger and 11 g per nut. Weigh one of yours and set the Nut mass slider; the page then shows the count per lever.
- 2 × M3 x 16 stainless socket head screw · Lever pivots; self-tap into the 2.6 mm holes in the collar fins. There is no locking, so check they are tight at each refill.
- 2 × M3 stainless washer · Under each pivot screw head.
- 2 × Small zip ties (up to 2.5 mm wide) · Through the hole under the last nut on each post.
- Stainless or galvanised wire, 1.5-2 mm, about 1 m · Tied through the two roof eyes to hang the feeder.
- Soda bottle with a PCO 1881 neck (0.5-2 L) · Holds the seed; screws in neck-down.
Assembly
- Slide the sleeve up onto the collar from below, with the two fins entering the open slots at the top of the sleeve, until the sleeve top sits just under the roof.
- Hold the sleeve up, set each lever against its fin with the short rounded nose resting on the sleeve's ear, and drive an M3 x 16 stainless screw with a washer through the lever into the fin. Stop when the lever still swings freely.
- Slide M10 nuts onto each hanging post (5 per lever at the defaults; the page shows the count for your sliders) and thread a zip tie through the hole just under the last nut.
- Tie wire through the two eyes on the roof and join it into a hanging loop above the bottle.
- Fill a PCO 1881 bottle with seed, turn the feeder upside down, screw the collar onto the bottle, turn it upright and hang it.
- Calibrate: hang a known weight equal to your trigger mass (for example a 320 g bag of water) on the perch ring; the ports should close, and reopen when you lift it off. Add or remove one nut on both levers to adjust.
Good to know
- A squirrel hanging from the counterweight arms holds the ports open. The arms and nut stacks are outside the feeder (the lowest nut hangs 52 mm from the nearest port at the defaults), and weight on them pushes the sleeve up, not down.
- Squirrels that cling to the collar roof, the bottle or the hanging wire can also reach the ports, and they can chew PETG. This is squirrel-resistant only against squirrels that stand on the perch ring or the sleeve; it is not squirrel-proof.
- Hang it on a long wire away from branches, fences and roofs that squirrels can jump from, and add a baffle if squirrels come down the wire.
- The trigger mass is calculated for a solid sleeve and solid levers and the nut mass you enter; lighter infill, pivot friction, ice and wet seed shift it. Check it with a known weight and tune with nuts or washers.
- The PCO 1881 thread is modelled from published neck diameters and its 2.7 mm pitch; necks vary between bottlers. Print the collar first and test-fit your bottle. 38 mm and other necks are not supported.
- The M3 pivot screws self-tap into PETG with no locking and may work loose outdoors; check them at each refill.
- The engine checks clearances and motion, not ice, snow, wear or seed spill. Some seed can fall from the ports, and the 2 mm drain holes also pass very small seed such as nyjer.
Comments