From the Loftsmith Workshop

Pocket watch case for Waveshare 1.75 in round AMOLED

Turns a bare Waveshare 1.75 in round AMOLED into something you can carry like a pocket watch. A hinged lid flips over the face, a small loop on the case and lid takes a chain, and a little stand props it up on the desk. Set the puck size and where the USB-C opening sits.

4 parts · 44 g · 230 × 87 × 40 mm

by Loftsmith Workshop

Round tan watch case with hinged lid and chain loops, beside a small white angled stand
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • case · PLA · Upright as modeled, back face on the bed. Prints together with the lid as one object (print group 'watch').

    About 14 g, 24 min at 2 walls/15%. Carries the hinge pin, the fluted crown and the bow at 12 o'clock, the twist-lock groove with its detent bump, and the magnet lobe at 3 o'clock. PLA is stiff, which keeps the knuckles and lugs true. It softens around 55 °C.

  • lid · PLA · Lies open and flat beside the case, outer face on the bed, engraved hour ticks facing up. Printed already on the hinge pin.

    About 8 g, 15 min. Full lid, a window lid you can see and tap the screen through (about 4 g), or no lid (Lid choice on Adjust).

  • bezel ring · PLA · Flat as modeled, grip flutes up, lugs on the bed.

    About 2 g, 6 min. Four lugs lock under the groove roof. The 1 o'clock lug sits on a 14 mm flexible arm whose tooth clicks past a bump at lock. PLA's stiffness gives the click; the arm bends along the layers.

  • stand · PLA · Base down as modeled.

    About 21 g, 36 min. Optional (Desk stand toggle). Slim stem, rounded arms and a 15.5 mm slot down the middle for a right-angle USB-C plug and its lead. Shown in ivory so the brass watch stays the subject; any colour works.

Print settings

Layer height
0.2 mm
Walls
2 walls (the page default). 3 walls makes a stiffer hinge and stand: about 61 g and 1 h 51 min for everything
Infill
15%
Supports
None. The groove roof, knuckle undersides and lug tops are all 45 degrees or less.
Notes
At the defaults all four parts come to about 46 g and 1 h 24 min at 2 walls/15% (case 14 g, lid 8 g, bezel ring 2 g, stand 21 g). The case and lid export as one object with their gaps kept. Do not split them, and do not add a brim inside the hinge. The case-and-lid object is about 144 x 77 mm and th

Hardware

  • 2 × 6 x 2 mm disc magnet (neodymium) · One in the case lobe at 3 o'clock, one in the lid's thumb lip. Pockets are 6.2 mm wide and 2.1 mm deep, so the magnets sit flush. Glue them in with the poles facing so they attract. Not needed with th
  • Cyanoacrylate glue · A drop per magnet pocket.
  • Right-angle USB-C cable · Optional, only for charging while the watch stands in the cradle. A straight plug sticks out about 20 mm and will not fit the stand.

Assembly

  1. Print the case and lid together. The lid lies open on the bed already threaded on the hinge pin. Work it shut and open a few times to free the knuckles.
  2. Glue one 6 x 2 mm magnet into the pocket on top of the case lobe at 3 o'clock and one into the pocket in the lid's thumb lip. Check that they attract before the glue sets.
  3. Drop the puck in screen-up and turn it so its USB-C port and buttons line up with the side opening.
  4. Lower the bezel ring so its four lugs drop through the four notches inside the rim, then turn it 30 degrees clockwise until it clicks. The click is the 1 o'clock lug's tooth passing the bump in the groove.
  5. To take the puck out, turn the ring firmly anticlockwise past the click, then lift it out.
  6. Close the lid until the magnets catch. To open it, lift the lid's thumb lip at 3 o'clock with a fingernail.
  7. For the desk, set the closed watch in the cradle with the bow on top. To charge it there, plug in a right-angle USB-C lead and run it back through the slot and out behind the stand.

Good to know

  • Measure your puck with calipers and set Puck diameter and Puck thickness to match. Board versions (1.75, 1.75-B, 1.75C, GPS) and their cases differ.
  • The bezel ring is held by its four lugs under the groove roof and kept from turning back by a click detent: one lug sits on a flexible arm and its tooth has to ride over a 0.35 mm bump. The ring does not press on the puck. It rests on its own ledge 0.15 mm above it, so the puck can shift that much.
  • The detent's holding force is not measured. The engine checks the geometry and that the arm bends within PLA's allowable stress (9.6 MPa against 16.7 MPa), but how firm the click feels needs a test print.
  • The USB-C opening is a U-cut placed by the USB-C opening position slider (150-210 degrees, 6 o'clock by default). It is not checked against a real board, so check that your port and buttons fall inside it before printing.
  • The lid is held by two small magnets, not a mechanical latch. Their pull is not modeled, and a hard knock in a pocket may open it.
  • The stand fits a right-angle USB-C plug only. A straight plug will not clear the cradle.
  • The full lid covers the touchscreen. Use the window lid to see and tap the screen with the lid shut.
  • PLA softens around 55 °C. Do not leave it on a car dashboard.

Comments