From the Loftsmith Workshop
Weighted jog wheel for EC11 / 6 mm D-shaft encoders
A big, heavy-feeling knob for scrubbing through video or audio with a rotary encoder. The ridged rim gives your fingers a grip, and the hex pockets on top hold nuts to add weight. Two dimples give your fingertip a place to spin it.
1 part · 21 g · 70 × 70 × 17 mm
Loading the 3D view
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- jog wheel · PLA · Bottom face down on the bed, as modelled; nut pockets and dimples face up
70 x 70 x 16.5 mm at the defaults. PLA works because it is stiff and the loads are small: the hardest-loaded spot is the D flat at 6.7 MPa against PLA's 16.7 MPa allowable. About 22 g and 34 min at 2 walls/15% infill.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 walls on the page stats (about 22 g, 34 min). For a heavier wheel with more spin, use 4 walls and 25% infill: about 38 g, 59 min
- Infill
- 15% gives the page figure. More infill adds plastic mass and inertia, and the wheel stays balanced because the layout is symmetric.
- Supports
- None. The hub relief steps at 45 degrees and the pockets and dimples open upward.
- Notes
- Print flat, bottom face down. The pocket mouths have a 0.6 mm lead-in chamfer. If the first pocket is too tight or too loose, change the Nut pocket clearance slider (0.05-0.4 mm). If the shaft is too tight or too loose, change the Shaft bore clearance slider (0.05-0.35 mm).
Hardware
- 8 × M6 hex nut, ISO 4032 (10 mm across flats x 5.2 mm) · Default setting. Any of M3, M4, M5, M6 or M8 works with the Nut size slider. Buy pockets x stacked nuts per pocket. 8 x M6 is about 21.6 g of steel (calculated from nut size).
- EC11 rotary encoder with 6 mm D shaft (4.5 mm across the flat), or any 6 mm D-shaft encoder or pot · This is what the wheel fits. It is not printed. Pick a detent-free version if you want the wheel to coast.
- Thin CA glue (optional) · A drop per pocket if the panel is tilted or upside down.
Assembly
- Measure how far the encoder shaft tip stands above the panel surface, then set the Shaft tip height slider to that (12-22 mm). The wheel height follows it.
- Print the wheel bottom face down with no supports.
- Press one nut into each hex pocket from the top, flats toward the rim, until it bottoms out 0.4 mm below the face. If you chose 2 nuts per pocket, stack two. Add a drop of thin CA glue if the panel will be tilted.
- Mount the encoder in the panel with its nut. Turn the wheel so the flat in the bore lines up with the flat on the shaft, then push it straight down until it sits about 1.5 mm above the panel.
- Flick the wheel at a dimple or at the fluted rim.
Good to know
- The wheel can only coast if the encoder has no detents. Most EC11 encoders click at 20 or 30 steps per turn, and those clicks will stop it quickly. Use a detent-free EC11 (or similar) for spinner-style use.
- The fit to the encoder assumes the bushing stands no more than 5.4 mm above the panel and the panel nut is no larger than 10 mm across flats and 2 mm thick. The D flat is taken as 7 mm long and 4.5 mm across. Check yours before printing.
- The bore fits 6 mm D shafts only. Knurled or split shafts are not supported.
- There is no 608 bearing option. The encoder's own shaft carries the wheel's weight, about 22 g of plastic plus the nuts at the defaults.
- Nuts are held by a press fit, and gravity keeps them seated on a flat panel. Glue them if the panel is tilted, vertical or upside down.
- Small wheels take fewer pockets than the slider asks for (for example 4 x M6 at 40 mm). The check line says how many fit. Below about 50 mm the dimple moves to the centre.
- The balance and inertia figures come from the CAD model, with the plastic treated as solid. They are estimates, not measurements. Fit, friction and spin-down time have not been tested on a real print.
Comments