From the Loftsmith Workshop

Lamp shade riser and finial, 1/4-27 thread, 16-75 mm lift

Lifts a lamp shade that sits too low on its bulb, so the shade clears the light and hangs where it should. A round finial screws down on top, and a small threaded bar with three tapped holes steps the height. Change the lift and the finial width to suit your lamp.

3 parts · 11 g · 62 × 83 × 104 mm

by Loftsmith Workshop

Amber knob finial on a ribbed riser with spindly legs, a curved shade piece and a small threaded bar
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • fit-strip · PETG · Flat on the bed, stud pointing up, no supports

    Print this first (about 4 g, about 10 minutes). It has three through-holes with female 1/4-27 threads at 0.05 / 0.10 / 0.15 mm play per flank (marked with 1, 2 and 3 dots) and one printed male stud. Screw each hole onto your harp stud and set Thread play to the snuggest one that still turns by hand.

  • riser · PETG · Upright, threaded mouth on the bed, stud pointing up, no supports

    About 3 g, about 11 minutes at the default 25 mm lift. Fluted spool body with a rounded shoulder; a 2.6 mm flat seat ring carries the shade saddle. PETG because it sits above the bulb and holds its shape at higher temperatures than PLA. The engine flags 10.0% of its surface as overhang; those faces

  • finial · PETG · Upright on its collar, threaded mouth on the bed

    About 5 g, about 14 minutes for the 26 mm ball with its pointed spire and neck bead. Ball, faceted and knurled heads all have 45-degree undersides, so none of them needs supports. The engine reports no overhang warning for the finial.

Print settings

Layer height
0.12 mm (fine layers for the 0.94 mm thread pitch)
Walls
3 walls recommended so the threads are solid perimeter plastic
Infill
15%
Supports
None. Print every part upright with its threaded mouth on the bed.
Notes
The page figures are the engine's defaults at 2 walls and 15% infill: about 12 g of PETG and about 37 minutes for all three parts. At the recommended 3 walls and 15% the engine estimates about 16 g and 49 minutes. Both times are at the engine's standard layer height; 0.12 mm layers take longer. Prin

Assembly

  1. Print the fit strip. Screw holes 1, 2 and 3 (1, 2 and 3 dots) onto your lamp's harp stud. Set the Thread play slider to the snuggest hole that still turns by hand without wobble: 0.05, 0.10 or 0.15 mm at the defaults.
  2. Measure how far the threaded stud sticks up above the harp top and set 'Harp stud length' to that value (6-16 mm). Set 'Riser height' to how far you want to lift the shade, and keep it at least stud length + 6 mm; for example, a 10 mm stud needs 16 mm or more and a 16 mm stud needs 22 mm or more.
  3. Unplug the lamp. Remove the old finial and lift the shade off the harp.
  4. Screw the riser onto the harp stud by hand until its foot seats on the harp top.
  5. Drop the shade's saddle (the ring at the centre of the spider fitter) over the riser's stud so it rests on the riser's flat top ring.
  6. Screw the finial down onto the stud until it is hand-snug on the saddle. Do not use tools. Your original finial fits the printed stud as well.

Good to know

  • Only for lamps with LED bulbs. Keep the riser and finial well away from the bulb. PETG softens around 75 °C.
  • The riser and finial are only mechanical parts and are never part of the electrical path. Unplug the lamp before fitting them.
  • The threads were checked as geometry in the Loftsmith engine, not printed or tested. Fine 0.94 mm pitch threads depend on your printer, so print the fit strip and set Thread play before printing the riser.
  • The printed 1/4-27 stud is the weakest point. Its check assumes a 40 N hand-tight clamp plus a 10 N push on the finial top, which gives 4.2 MPa at the defaults against PETG's 5.0 MPa allowable across the layers. Tighten the finial by hand only. A metal riser suits a heavy shade or a lamp that gets k
  • The riser's blind bore needs the lift to be at least the harp stud length + 6 mm. In engine numbers: at the 16 mm minimum lift the longest harp stud that passes is 10 mm, and a 16 mm stud needs at least 22 mm of lift. The 'Harp stud fits the blind bore' check on the Check tab shows the limit for you
  • The shade saddle is assumed to be about 1.5 mm thick with a hole of about 7.6 mm. A saddle much thicker than about 4 mm leaves fewer than 6 thread turns for the finial.
  • Plays are per flank. The fit strip brackets the chosen play by ±0.05 mm, and the slider runs from 0.05 to 0.18 mm.

Comments