From the Loftsmith Workshop

Waveshare ESP32-P4 4.3 inch ebook reader case with page keys

A case that turns a Waveshare ESP32-P4 4.3 inch board into a little ebook reader you can stand on the desk. The screen sits in an open window, with two page keys beside it and a kickstand folding out the back. Change the board size and key spacing to match your own.

5 parts · 90 g · 116 × 96 × 121 mm

by Loftsmith Workshop

Dark grey square case with a screen window and two page keys, leaning back on a kickstand
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • front shell · PETG · Face down on the bed (the window bevel and the 2.4 mm front-edge chamfers print as 45-degree overhangs, no supports)

    About 47 g, 66 min. The two page keys are flexure tongues cut into this shell, so it must be PETG. Has 6 bosses for M2.5 heat-set inserts, 2 posts for the switch plate and the charger-module cradle.

  • switch plate · PETG · Flat, switch side up

    About 3 g, 8 min. The two 6 x 6 mm tactile switches stand on it with their pins through the holes; solder the wires on the back.

  • battery door · PETG · Inner face down

    About 13 g, 20 min. Rolled grip back with strap slots beside the cell and vent slots under it; held by 2 countersunk M2.5 screws.

  • back plate · PETG · Inner face down, hinge knuckles up

    About 23 g, 34 min. Vent slots under the stand; held by 4 countersunk M2.5 screws.

  • kickstand · PETG · Outer face down

    About 4 g, 10 min. The barrel has a flat bottom, so it prints without supports.

Print settings

Layer height
0.2 mm
Walls
2 walls (the page stats); 3 walls is a little stiffer around the inserts
Infill
15%
Supports
None
Notes
Build report at 2 walls / 15%: about 93 g of PETG and 2 h 24 min for all five parts at default sliders. At 3 walls / 15% it is about 119 g and 3 h 4 min. Print everything in PETG: the front shell must be PETG for the flexure keys, and PETG copes better than PLA with warmth near the cells. The larges

Hardware

  • Waveshare ESP32-P4-WIFI6-Touch-LCD-4.3 board · Defaults are 66.8 x 114.4 mm outline, 94.4 x 56.96 mm active area and 12 mm deep, from a reseller drawing. Measure your board and set the Board width, Board length and Board depth sliders (each outlin
  • 1S LiPo pouch cell with its own protection board (e.g. about 50 x 34 x 10 mm) · Size it with the Battery sliders. A second identical cell is optional (Cells = 2); see the parallel-wiring step.
  • 1S Li-ion USB-C charge and protection module (about 28 x 17.5 x 5 mm) · The cradle and port opening fit that envelope; measure yours. Leave it out only if Waveshare's documentation confirms the board charges a cell through its own battery header.
  • 2 × 6 x 6 x 5 mm through-hole tactile switch · Page back and page forward; wire them to free GPIOs.
  • 6 × M2.5 brass heat-set insert (3.6 mm hole)
  • 6 × M2.5 x 6 countersunk screw · 4 for the back plate, 2 for the battery door.
  • 2 × M2 x 5 pan-head self-tapping screw · Hold the switch plate on its posts.
  • M3 x 35 screw and M3 nyloc nut · Kickstand hinge pin. Tighten the nut until the stand holds its angle.
  • 10 mm hook-and-loop strap, about 120 mm long · 1 strap; 2 with Cells = 2. Each one threads through the door's strap slots around one cell.
  • Thin silicone hookup wire (about 1.8 mm outside) and an MX1.25 2-pin lead · Wire the cell to the module's B pads, and the module's OUT pads to the board's battery header.
  • Double-sided foam tape · Holds the charger module in its cradle.

Assembly

  1. Measure your board and set Board width, Board length, Board depth and Active area offset before printing.
  2. Press the six M2.5 heat-set inserts into the bosses of the front shell (four at the ends of the screen bay, two at the ends of the grip).
  3. Push the two tactile switches through the switch plate and solder a wire pair to each. Screw the plate onto its two posts in the grip with the M2 screws, so each switch stem sits under a key nub.
  4. Fix the charger module in its cradle under the lower key with foam tape, its USB-C port pushed into the opening in the grip's outer wall.
  5. Lay the board face down in the shell so the screen sits behind the window. The end bosses locate it along its length.
  6. Wire the cell's protected lead to the module's B+ and B- pads. Run a lead from the module's OUT+ and OUT- pads along the bottom of the grip, through the notch in the grip wall and along the channel at the bottom end, to the board's battery header. Check polarity before you plug it in.
  7. Two cells (Cells = 2): use two identical protected cells, charge both and measure them, and join them only when their voltages are within about 0.05 V. Solder both leads in parallel to the module's B pads (red to B+, black to B-). The second cell's lead runs down the side of the bay beside the strap
  8. Strap each cell to the inside of the battery door with its own hook-and-loop strap. Put the door on and fit 2 countersunk M2.5 screws.
  9. Put the kickstand barrel between the back plate's knuckles and push the M3 x 35 screw through. Tighten the nyloc nut until the stand holds its angle, then fit the back plate with 4 countersunk M2.5 screws.
  10. Charge through the module's USB-C on the grip edge. The board's own USB-C and microSD are reached through the slot in the bottom end.

Good to know

  • The default outline (66.8 x 114.4 mm), active area (94.4 x 56.96 mm) and 12 mm depth come from a reseller drawing and an estimate, not from a confirmed Waveshare mechanical drawing. Measure your board, or check the Waveshare wiki (https://docs.waveshare.com/ESP32-P4-WIFI6-Touch-LCD-4.3), and set the
  • The access slot is on the bottom short edge. It assumes the board's USB-C and microSD are on a short edge. If yours are on the other short edge, turn the board round and rotate the image in firmware.
  • The reseller listing describes an MX1.25 lithium battery header. This design does not confirm whether the board charges a cell itself, so it includes a bay for a separate 1S charge-and-protection module. Use one charger only: the module, or the board's own if Waveshare confirms one, never both.
  • Use only LiPo cells with their own protection board. Join two cells only if they are identical and within about 0.05 V of each other. The case does not charge the cells or protect them, and the battery bay is vented and not sealed.
  • Key feel, hinge friction and the 70 g board mass used in the balance and stability checks are estimates. The keys and stand need a real print to judge.
  • The front face is flat on purpose: it prints face down. Its outer edges are 2.4 mm chamfers rather than rounds, so the case reads crisp at the front and rolled at the back.

Comments