From the Loftsmith Workshop

Coffee bean hopper extension with lid, sized in grams

Gives your grinder room for a whole bag of beans, so you're not topping up every morning. It sits on the hopper rim with a lip that drops inside, and the lid has a pouring notch at the front. Change the rim length and width to match your grinder.

2 parts · 114 g · 118 × 106 × 111 mm

by Loftsmith Workshop

Cream ribbed container with a brown lid and front notch, stacked on a grey rounded base
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • collar · PETG · Upside down, top rim on the bed (printRotate 180, 0, 0)

    118 × 93 × 108 mm at the defaults, ~86 g, ~123 min. With the top rim on the bed, the 45 degree skirt flares inward as it rises, so no supports are needed. Walls are 1.6 mm at the flute valleys and 2.4 mm at the crests. I chose PETG because it is tougher than PLA and takes warmer kitchen temperatures

  • lid · PETG · Top face down (printRotate 180, 0, 0)

    112 × 103 × 11 mm with the thumb tab, ~29 g, ~41 min. The capacity is engraved 1.2 mm deep on the bed side. An 8 mm plug drops into the collar with 0.3 mm clearance per side.

  • fit-ring · PETG · Skirt face down (printRotate 180, 0, 0)

    Optional, only made when 'Add a quick fit-test ring' is on: ~10 g, ~18 min. It is the flat skirt plus the first 6 mm of lip, for checking the rim size and clearance before the full print.

Print settings

Layer height
0.2 mm
Walls
2 walls (the page default; the 1.6 to 2.4 mm walls fill with perimeters either way)
Infill
15%
Supports
None
Notes
Default figures from the Loftsmith build: collar + lid ~119 g, ~2 h 51 min at 2 walls / 15% (collar ~86 g, ~123 min; lid ~29 g, ~41 min). At 3 walls / 15% the build reports ~147 g, ~3 h 31 min. PETG on a textured or glue-coated plate. Taller collars (more grams or a smaller rim) take longer: 500 g o

Assembly

  1. Measure your hopper's rim: the inside length and width (or inside diameter if round), the corner radius and the wall thickness at the top edge. Enter them on the Adjust tab with the shape choice.
  2. Optional: switch on 'Add a quick fit-test ring' and print just that ring (~18 min). It should drop into the rim and sit flat without rocking. If it is tight, raise Lip clearance by 0.1 to 0.2 mm; if it rattles, lower it.
  3. Set 'Extra beans to hold' and choose medium or dark roast (dark beans take more space per gram, so the collar comes out taller).
  4. Print the collar and the lid upside down as exported. No supports are needed.
  5. Take off the hopper's own lid, drop the collar's lip into the rim until the skirt rests on the rim edge, then fill with beans and press the printed lid into the top.

Good to know

  • Not certified food-safe. PETG is a common choice for dry food contact, but layer lines can trap oils and dust, and colourants vary by brand. Wash it before use and judge for yourself.
  • Grams are estimates from bulk density (0.34 g/cm³ medium, 0.27 g/cm³ dark). Real beans vary roughly from 0.25 to 0.37 g/cm³, so the same collar holds more of a light roast and less of a very dark one.
  • Some bean-to-cup machines and grinders use a magnet or switch in their original lid to detect that the hopper is closed. This printed lid has no magnet, so those machines may refuse to run with it.
  • The lip is a simple slip fit on a flat-topped rim. Hoppers with a lid step, a bayonet or a sloped rim may need the lip depth or clearance adjusted, and some will not fit this design.
  • The smallest corner radius is 10 mm. If your rim's corners are tighter, set 10: the lip still fits but leaves a small gap in each corner.
  • The tilt-retention check is a rigid-body estimate. A 10 mm lip combined with 1.0 mm clearance fails it on a 110 mm rim, so use a deeper lip if you need the loose fit.
  • A small rim combined with a large gram target can make the collar taller than 250 mm. The 'Fits the printer height' check will then fail, so lower the grams. Collars taller than 180 mm do not fit an A1 mini.
  • Checked in the Loftsmith engine only. It has not been printed or tried on a real grinder.

Comments