From the Loftsmith Workshop

Raspberry Pi 500/500+ laptop screen lid, 140-205 mm screens

Turns a Raspberry Pi 500 or 500+ into a little laptop by giving it a screen to sit behind. The frame holds a display on two hinge pins at the back, and the lid folds down flat when you're done. Change the screen width and height to match your display.

11 parts · 86 g · 297 × 90 × 146 mm

by Loftsmith Workshop

White keyboard computer with a dark open screen frame held on two orange hinge brackets
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • frame · PETG · Screen face down, flat on the bed; no supports

    176.8 x 127.1 x 15.7 mm at the defaults, about 42 g and 58 min. The hinge barrel along its bottom edge prints as part of it. PETG because it sits against a screen that runs warm.

  • arm-right · PETG · Standing on its flat hinge face (the stop lug is at the base)

    Continues the hinge barrel out to the clamp. The M5 nylock nut slides into the side slot, and an M3 heat-set insert goes into the tongue.

  • arm-left · PETG · Standing on its flat hinge face

    Mirror of arm-right.

  • clamp-right · PETG · Outer end face down, so the side profile lies flat and the hinge bore prints vertical

    52.7 x 75.4 x 25 mm at the defaults, about 16 g. Layers run along the C-shape, so the jaws bend along the layers. PETG for toughness at the hinge and the thumb screw.

  • clamp-left · PETG · Outer end face down

    Mirror of clamp-right.

  • washer ×2 · PETG · Flat

    Friction faces between each arm and its clamp, 18.2 mm OD x 1.5 mm. Replaceable when worn.

  • clip-right ×2 · PETG · Flat, rounded face up

    Turn clips that hold the screen in the frame.

  • clip-left ×2 · PETG · Flat, rounded face up

    Same shape as clip-right; listed separately only because the left ones are placed mirrored.

Print settings

Layer height
0.2 mm
Walls
3 recommended for the clamps and arms (the page figure is for 2 walls)
Infill
15%
Supports
None
Notes
PETG throughout. At the page's default settings (2 walls, 15% infill) the whole set is about 89 g and 2 h 56 min on a Bambu A1. With the recommended 3 walls and 15% infill it is about 116 g and 3 h 41 min. At the defaults every part fits a 180 mm bed (the frame is 176.8 mm wide). Screens wider than

Hardware

  • 2 × M5 x 35 socket head screw · Hinge bolts, inserted from the outside of each clamp
  • 2 × M5 nylock nut · Captured in the arm slot, so the bolt can be tightened from outside with a 4 mm hex key
  • 2 × M5 conical spring washer · Under each hinge bolt head; keeps the friction steady as the faces wear
  • 2 × M4 x 12 knurled thumb screw · Clamp screws, finger-tight only
  • 2 × M4 hex nut · In the pocket under each clamp's top jaw
  • 6 × M3 heat-set insert (4.1 mm hole, 5.7 mm long) · 4 in the frame's back borders for the clips, 1 in each arm tongue
  • 2 × M3 x 6 countersunk screw · Frame to arm tongues, from the front of the bottom bezel
  • 4 × M3 x 6 button head screw · Turn clips
  • 2 × Small felt or rubber pad (optional) · Under each thumb screw tip so it does not mark the case

Assembly

  1. Press four M3 heat-set inserts into the frame's side borders from the back, and one into the front face of each arm's tongue.
  2. Slide an M5 nylock nut into the slot under each arm. Push an M4 nut into the pocket under each clamp's top jaw.
  3. Slide each clamp onto a rear corner of the computer from behind: top jaw over the case, bottom jaw under it, end wall against the side. Thread in the M4 thumb screws with a felt pad under the tip and tighten finger-tight only.
  4. Drop each arm's tongue into the slot at the end of the frame's hinge barrel from behind. Fix it with an M3 x 6 countersunk screw from the front of the bottom bezel.
  5. Hold the lid between the clamps with a printed washer between each arm and its clamp. From the outside, push an M5 x 35 screw with a conical spring washer through the clamp into the nylock nut.
  6. Tighten each hinge screw with a 4 mm hex key until the lid stays where you leave it at any angle. The check calls for about 112 N of clamp per hinge at the defaults.
  7. Lay the screen into the frame from the back, plug in its HDMI and USB leads, then turn the four clips over its edge and fix them with M3 x 6 screws.

Good to know

  • The Pi 500's rear-edge profile isn't published. The clamps are built around the product brief's maximum size (286 x 122 x 23 mm; 500+: 312 x 123.06 x 35.76 mm) with an assumed 8 mm corner radius. Print one clamp first and check its fit.
  • Each clamp covers the outer 14 mm of each end of the rear edge, and its top jaw reaches 20 mm forward from the back. Check that these areas of your case are free of ports and keys.
  • The rear of the computer sits on the 4 mm bottom jaws, which tilts the keyboard about 2 degrees toward you.
  • Hinge friction and the tipping margin are engine estimates, not test results. They assume 0.25 friction between the faces, a 3 N press near the top of the screen and the computer's weight centred in its case. Weigh your computer and screen and set the sliders.
  • It fits screen modules 140-205 mm wide, 80-140 mm tall and 8-16 mm thick at the edge. The front lip covers 3.5 mm of each edge, so a screen with less than 3.5 mm of black border or connectors sticking out past its outline will not fit as drawn.
  • The cables are not routed: the back of the lid is open so leads plug straight into the screen, and you run them down behind the hinge yourself.
  • Keep the thumb screws finger-tight. Overtightening can mark or crack the case.

Comments