From the Loftsmith Workshop
Album art desk frame for 4 in ESP32 panels (4848S040)
Turns a small ESP32 screen into a proper desk piece for showing album art. A light mat frames the picture, and the stand clicks through a few tilt angles so you can set the glare where you like. There's room behind for the lead.
4 parts · 89 g · 106 × 107 × 110 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- frame · PLA (charcoal) · Face down on the plate, window and mat on the first layers
106.4 x 113.5 x 27.6 mm at the defaults, about 50 g and 69 min including the mat inlay. Stiff everyday PLA; use PETG if it sits in a sunny window.
- mat · PLA (cream), filament slot 2 · Printed inside the frame in its first 0.8 mm (flush inlay)
About 3 g plus 4 colour changes on an AMS. On a single-filament printer, print it in the frame colour or set the Mat width slider to 0.
- spacer · PLA · Flat, either face down
Ring that presses the panel onto the lip; about 9 g, 16 min. It has a notch for the lead on the cable side.
- back cover · PLA (charcoal) · Inner face down, hinge ears pointing up
About 22 g, 35 min. Two in-plane snap beams (2.2 x 30 mm) flex 0.9 mm to clip into the frame; layers run along the beams.
- leg · PLA (charcoal) · Flat on its chamfered face
About 8 g, 15 min. The click dimples are on both sides of the hub.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- About 94 g and 2 h 25 min for all four parts at 2 walls / 15% infill, including about 2 g of purge for the cream mat. The frame prints face down, so the front comes out with the plate's finish. PLA for indoor desks; PETG if it sits in direct sun.
Hardware
- M3 x 25 mm screw · Hinge pin through both ears and the leg hub.
- M3 nyloc nut · Tighten until the ears just grip the hub; this sets the click.
- 2 × M3 washer · One under the screw head, one under the nut.
- USB-C lead, about 4 mm thick (right-angle plug recommended) · The frame leaves 8 mm behind the panel by default; raise the 'Space behind the panel' slider if your plug needs more. 5 V USB-powered panels only.
Assembly
- Print the frame face down (with the cream mat on an AMS, or all in one colour), and print the spacer, back cover and leg flat.
- Lay the frame face down and slide the panel in from the back, screen first, until it rests on the 2.4 mm lip.
- Plug the USB-C lead into the panel, run it down the inside of the frame on the cable side and press it sideways into the slot low in the side wall so it leaves from the side.
- Drop the spacer ring in behind the panel with its notch over the lead.
- Press the back cover in until both snap teeth click into the side walls. To open it later, push a coin into the slot beside each snap beam and lever the beam inward.
- Fit the leg hub between the two hinge ears and push the M3 x 25 screw through with a washer at each end. Tighten the nyloc nut until the ears just grip the hub and the leg clicks from one tilt to the next.
- Stand the frame on its front edge and swing the leg out to the tilt you want.
Good to know
- The click detents only work once the M3 nyloc nut squeezes the hinge ears onto the leg hub. How firmly they click depends on that tightness and on the print, and it has not been tested.
- The tip check assumes the panel weighs at least 60 g. At the lightest setting (8 degree tilt, no mat), a push of about 1.1 N at the top of the screen tips it back; at the defaults it takes about 1.6 N. Tap gently near the top edge or use a steeper click.
- The USB-C port position on these panels was not modelled. A right-angle USB-C plug fits best; raise the 'Space behind the panel' slider if your plug sticks out further than about 8 mm behind the board.
- The window assumes the active area is centred on the module. Check your panel before printing; the lip only overlaps the border by 7.05 mm of 7.35 mm on the Guition.
- The Measured preset assumes a square active area.
- Only for 5 V USB-powered panels. Do not put relay or mains-switching versions in it.
- PLA softens around 55 C. Print it in PETG if it sits in a sunny window or near a heat source.
- The snap fit, the clicks and the fit of your panel were checked in the Loftsmith engine, not on a real print. A small test print of one corner is worth it if your panel's outline differs from 86.5 mm.
Comments