From the Loftsmith Workshop

Macro deck console for 7 in ESP32-P4 panel (JC1060P470C)

A little desk stand that tilts a 7 in ESP32-P4 panel toward you, so your macro buttons sit within easy reach. The sides have slim slots cut into them, and a dark frame holds the screen in place. Change the tilt and the board size to match your own panel.

10 parts · 125 g · 179 × 107 × 114 mm

by Loftsmith Workshop

Light grey wedge-shaped desk stand with slotted sides and a dark frame around a slanted opening
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • stand · PLA · Upright on its base (as it sits on the desk)

    177.5 x 99.9 x 104 mm at defaults; about 97 g, 2 h 21 min at 2 walls/15%. Walls rise straight from the bed; the back wall leans 9 degrees. No supports. The side walls thicken to 6.5 mm at the top, where the M2 screws bite.

  • bezel · PLA · Back face down, pocket opening up

    178.5 x 117.6 x 11.5 mm at defaults; about 26 g, 39 min. The 2.5 mm board ledge prints on the bed, so there is no overhang. The 178.5 mm width fits a 180 mm bed with little margin.

  • tab bottom-left · PLA · Flat

    Swivel corner tab, 2.4 mm thick, about 4 min.

  • tab top-left · PLA · Flat

    Swivel corner tab, 2.4 mm thick, about 4 min.

  • tab bottom-right · PLA · Flat

    Swivel corner tab, 2.4 mm thick, about 4 min.

  • tab top-right · PLA · Flat

    Swivel corner tab, 2.4 mm thick, about 4 min.

  • foot pad ×4 · TPU 95A · Flat, rounded face up

    20 x 8 x 1.6 mm grip pads, about 5 min each. TPU gives the grip the slide check assumes.

Print settings

Layer height
0.2 mm
Walls
2 walls (the page figures: about 130 g, 3 h 42 min for all parts). 3 walls gives the screw walls more material: about 175 g, 4 h 49 min.
Infill
15%
Supports
None
Notes
Stand, bezel and tabs in PLA; foot pads in TPU 95A. At the defaults every part fits a 180 mm bed (Bambu A1 mini). Boards wider than about 165 mm need a 256 mm bed.

Hardware

  • 4 × M2 pan or socket head screw · M2 x 20 at the default 9 mm board thickness. The script picks the length from the board thickness: M2 x 16 for 5-6 mm boards, up to M2 x 30 for 16 mm. Each screw goes through a tab and the bezel into
  • USB-C cable, straight plug · A lead of about 4 mm diameter with a plug body under 12.5 x 7 x 26 mm. It runs inside the stand and leaves through the arched notch at the back.
  • Thin double-sided tape or a drop of glue · Holds the four TPU pads under the base flange.

Assembly

  1. Print the stand upright, the bezel back face down, the four tabs flat, and the four foot pads in TPU.
  2. Stick the pads under the front and rear strips of the stand's base flange, where the base is solid.
  3. Set the bezel on the stand's sloped seat so its edges line up with a thin shadow line all round.
  4. Lay the USB-C lead into the arched notch at the bottom of the back wall (it drops in from below), bring it up through the stand and out through the bezel's back window, then plug it into the board.
  5. Lower the board into the pocket, glass facing out. It rests on the 2.5 mm ledge with the glass flush to the bezel front.
  6. Swing each tab over its corner of the glass border and drive an M2 screw through the tab and bezel into the pilot in the stand's side wall. Stop when the tab is snug; do not overtighten into PLA.
  7. To take the board out, loosen each screw about a turn, swing the tabs 90 degrees outward over the bezel border, and lift the board straight out.

Good to know

  • The pocket uses published sizes: board 164.9 x 104 mm, active area 154.21 x 85.92 mm, 260 g. Sources disagree on body depth, so measure your board's edge thickness and the height of the parts on its back, and set those sliders before printing.
  • The USB-C port position is an assumption: a straight plug coming out of the back of the board, 35 mm in from the chosen side and at mid-height. If your port is on an edge, use a right-angle lead; the stand's interior is open.
  • Tipping and sliding are engine estimates, not physical tests. They assume a friction of 0.5 for the TPU pads and a conservative weight for the PLA. At the defaults a 2 N tap has a 1.9x margin against tipping and 2.52 N of grip against 1.41 N of push.
  • The angle is fixed when you print. To change it, reprint the stand and the bezel; the top screw holes can move a fraction of a millimetre at steep angles.
  • At 60 degrees with a 3 N tap and a 16 mm board all at once, the slide margin falls just below 1.2x. Keep taps light at steep angles, or add weight inside the base.
  • The tabs are placed on the assumption that the black glass border is centred around the touch area. They clear it by more than 1 mm with that assumption. If your panel's border is offset, check the corners before tightening.
  • PLA softens at about 55 °C. This is an open, vented stand, not a sealed or heat-rated enclosure.

Comments