From the Loftsmith Workshop

Raspberry Pi Touch Display 2 10 in case, fits 180 mm beds

Gives a Raspberry Pi Touch Display 2 a proper home on your desk instead of leaning on a stack of books. A dark frame holds the screen and two angled feet tip it back so it's easy to read. Change the tilt or how much the frame overlaps the glass.

10 parts · 135 g · 291 × 148 × 198 mm

by Loftsmith Workshop

Dark rectangular screen frame propped on two orange triangular feet, tilted back
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • frame-bottom-right · PLA · Front face down on the bed

    147.4 x 106.8 x 18.5 mm, ~25 g, ~38 min. Carries two dovetail tongues; the first piece in the assembly.

  • frame-top-right · PLA · Front face down on the bed

    147.4 x 96.8 x 18.5 mm, ~24 g, ~37 min.

  • frame-bottom-left · PLA · Front face down on the bed

    137.4 x 106.8 x 18.5 mm, ~24 g, ~37 min.

  • frame-top-left · PLA · Front face down on the bed

    137.4 x 96.8 x 18.5 mm, ~24 g, ~36 min. Goes on last; it takes two tongues.

  • clip-bottom-right · PLA · Flat

    Turn clip, 11 x 18.4 x 3 mm, ~5 min.

  • clip-top-right · PLA · Flat

    Turn clip, ~5 min.

  • clip-bottom-left · PLA · Flat

    Turn clip, ~5 min.

  • clip-top-left · PLA · Flat

    Turn clip, ~5 min.

  • foot-right · PLA · On its flat inner face

    147.9 x 77.9 x 8 mm, ~18 g, ~28 min. In wall mode this becomes wall-bracket-right, printed with its wall face down.

  • foot-left · PLA · On its flat inner face

    Mirror of foot-right, ~18 g, ~28 min. In wall mode this becomes wall-bracket-left.

Print settings

Layer height
0.2 mm
Walls
2 (page figure: ~139 g, ~3 h 52 min for everything); 3 walls at 15% recommended around the inserts and dovetails: ~181 g, ~4 h 59 min
Infill
15%
Supports
None
Notes
PLA. Frame corners print face down, each under 148 mm, so every piece fits a 180 mm bed (A1 mini). With the 2-piece split, the halves are 193.7 mm long and need a 256 mm bed. If the dovetails are tight or loose, change the Dovetail clearance slider. Turn on the fit-test toggle first for a 45 mm corn

Hardware

  • 8 × M3 heat-set insert (4.1 mm hole, 5.7 mm long) · One in the rear rim of each frame piece for the clips, two in the outside of each bottom end wall for the feet or brackets.
  • 4 × M3 x 8 button-head screw · Clip pivots; tighten lightly so the clips still turn.
  • 4 × M3 x 12 button-head screw · Feet or wall brackets into the end-wall inserts.
  • 2 × 4 mm wood screw with wall plug, head up to 8 mm · Wall mode only, for the keyholes.

Assembly

  1. Optional first: turn on 'Add a corner fit-test piece', print it and drop a corner of your panel in. It should sit flat on the lip with a little play. Adjust Panel clearance or Bezel overlap if needed.
  2. Press the 8 M3 heat-set inserts in: one into the rear rim of each frame piece, two into the outside of each bottom end wall.
  3. Lay frame-bottom-right face down. Slide frame-top-right and frame-bottom-left straight down onto its dovetail tongues so the front faces sit level, then add frame-top-left last, which takes two tongues at once.
  4. Lay the screen face down into the frame so the glass rests on the front lip.
  5. Screw the four turn clips onto the rear rim with M3 x 8 button-head screws and turn each one over the back edge of the panel. Each corner is now held front and back, so the dovetails cannot slide apart.
  6. Desk: screw the two feet to the end walls with M3 x 12 button-head screws. Wall: switch Mount to wall, print the brackets instead, screw them on the same way and hang the keyholes on two screws in the wall.
  7. Plug the USB-C lead into the Pi and run it down behind the screen and out the back.

Good to know

  • The panel size used is 248.1 x 166.9 x 15.5 mm. Measure your unit before printing and print the corner fit-test piece first.
  • Check that your screen's black border is wider than the Bezel overlap setting (5 mm by default) so the lip does not cover the picture.
  • The clips need a flat strip about 6 mm wide around the edge of the panel's back. Any connector or button on the panel's edges would be covered by the frame walls.
  • The frame does not touch the Pi, and its position on the panel's back is only approximate. Wall brackets leave 36 mm behind the frame, assuming the Pi and cooler stand no more than 28 mm off the panel.
  • The tip check covers a 2 N tap at the top of the screen when the screen and Pi weigh at least 153 g at 15 degrees tilt. It does not cover knocks, pulls on the cable or drops.
  • PLA softens around 55 °C. Print in PETG if the screen sits in sun or next to a heat source.
  • Fits, clip grip and dovetail tightness are checked in the engine, not on a real print. Expect to tune the clearance sliders for your printer.

Comments