From the Loftsmith Workshop

Sunrise alarm clock case: LED ring dome + GC9A01 screen

A case for waking up to light instead of a buzzer. A frosted dome sits in the middle of the base and spreads the glow from an LED ring. The round hole in the front is where the GC9A01 screen sits. Change the dome size or the screen tilt to suit your bedside.

3 parts · 166 g · 159 × 127 × 96 mm

by Loftsmith Workshop

Dark blue rounded base with a white frosted dome on top and a round opening in the front
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • horizon base · PLA (any colour; dusk blue shown) · Upside down, top face on the bed (printRotate 180 about X)

    158 x 127 x 45 mm, about 94 g and 2 h 10 min at 2 walls/15%. No supports: the ring seat, dome socket, ray grooves, port notch and screen window are short bridges of 7.5 mm or less. Press four M3 heat-set inserts into the corner bosses.

  • sun dome · White PETG (diffuser) · Rim down

    96 x 97 x 52 mm, about 25 g and 41 min. PETG because it sits over the LEDs and takes the twist-lock lugs better than PLA. Print without supports; the thin shell builds up layer on layer to the top. Add a brim if your first layer is unreliable.

  • bottom plate · PLA · Flat, as modelled

    158 x 127 x 7 mm, about 47 g and 1 h 5 min. Its chamfered edge is the foot of the clock; carries the ESP32 cradle and the ledge under the screen.

Print settings

Layer height
0.2 mm
Walls
2 walls (page default); the dome's 1.2 mm wall prints as solid perimeters
Infill
15%
Supports
None
Notes
At 2 walls and 15% infill the three parts total about 171 g and 4 h 4 min (base about 94 g / 2 h 10 min, plate about 47 g / 1 h 5 min, dome about 25 g / 41 min). At 3 walls and 15% infill it is about 227 g and 5 h 22 min. Print the dome in white PETG; base and plate in PLA. A thicker diffuser wall s

Hardware

  • WS2812 / NeoPixel LED ring, 24 LEDs (66 mm outside, 52.5 mm inside) · Or a 16-LED ring (44.5 mm outside, 31.75 mm inside) with the LED ring choice. If a clone ring's inside diameter differs, measure it and set the inner-diameter slider (-1 to +1.5 mm).
  • GC9A01 1.28 in round display module (40.4 x 37.5 mm board) · Slides into the rails behind the front window.
  • ESP32-C3 Super Mini (22.52 x 18 mm) · Runs WLED or ESPHome; USB-C faces the back.
  • 4 × M3 heat-set insert (about 4.1 mm hole, 5.7 mm long)
  • 4 × M3 x 8 countersunk screw · Hold the bottom plate on.
  • USB-C lead and 5 V USB supply · Plug body up to 12 x 6.5 mm fits the back notch.
  • Thin hook-up wire · Ring and screen to the ESP32; solder wires directly rather than using header pins.
  • 4 × Stick-on rubber feet (optional)

Assembly

  1. Press four M3 heat-set inserts into the corner bosses inside the base (base upside down on the bench).
  2. Solder wires to the GC9A01 module, then slide it into the rails behind the front window, display facing out. It rests against the inside of the front wall.
  3. Solder wires to the LED ring pads and feed them down through the slot at the back of the ring seat. Press the ring into its seat; a dot of hot glue at the pads stops it lifting.
  4. Solder the ring and screen wires to the ESP32-C3. Slide the board forward on the bottom plate until its antenna end is under the hood, with the USB-C port at the back edge.
  5. Fit the bottom plate so the USB-C port lines up with the back notch. Fasten it with four M3 x 8 countersunk screws from below.
  6. Drop the dome into its socket with the three lugs in the notches, then turn it 25 degrees clockwise (seen from above) to lock it. Turn it back to lift it off.
  7. Plug in the USB-C lead at the back and set a brightness or current limit in WLED or ESPHome before running full white.

Good to know

  • Checked in the Loftsmith engine only, not printed or tested. Fit, clearances, retention, cable bend and tipping are geometry and estimate checks.
  • The screen window assumes the round display is centred on the 40.4 x 37.5 mm board. Check your module before printing the base.
  • How even the glow looks depends on the filament. The design keeps the diffuser at least 1.5 times the LED spacing from the LEDs, but that is a rule of thumb. If you see hotspots, try a thicker wall or line the dome with parchment paper.
  • A 24-LED ring at full white can draw more current than a weak USB supply provides. Use a 5 V USB supply only and set a brightness or current limit in your firmware.
  • The dome is held by three lugs under a 1.8 mm PLA lip. Only friction stops it turning, there is no click detent, so don't carry the clock by the dome.
  • The LED ring sits on three centring ribs and is not clamped; use a dot of hot glue at the pads.
  • At the default settings it fits a 180 mm bed. A large dome with a wide horizon reaches 198 mm wide and needs a 256 mm bed.
  • Internal wiring is not modelled; leave slack between the base and the plate.
  • This is a lamp and clock case; it makes no claim about sleep or health.

Comments