From the Loftsmith Workshop

Living hinge thickness test strip, 2-7 layers, PETG/PLA/TPU

Print this before you commit to a living hinge, so you know how thin a web can go in your filament before it cracks. Each flap hangs off the spine on a hinge a layer or two thicker than the last, numbered so you can flex them and compare. Change the layer height to match your slicer settings.

1 part · 16 g · 129 × 47 × 4 mm

by Loftsmith Workshop

Flat teal strip with rows of small numbered flaps joined to a central spine by thin hinges
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • strip · PETG (or PLA / TPU 95A, the material you · Flat as modelled, hinge webs on the bed

    One piece: 12 hinge tabs on a spine (front row S = short flex length, back row L = long), three zig-zag springs with pull tabs on the right. 128.8 x 47.1 x 4.4 mm at the defaults.

  • labels · Same material as the strip, second colou · Printed inside the strip as the top 0.6 mm (filament slot 2)

    Layer counts over each column, line counts on the spring pull tabs, the layer height and the S/L row marks. Single-filament printers: delete this part in the slicer and the digits stay as 0.6 mm recesses.

Print settings

Layer height
0.20 mm with a 0.20 mm first layer at the defaults. Set your slicer's layer height and first layer height to exactly the two slider values, or the webs will not be whole layers.
Walls
2
Infill
15%
Supports
None
Notes
About 19 g and 29 minutes in PETG at 2 walls and 15% infill, including about 2.4 g of purge for the second colour (estimate from the build report). 3 walls and 15% infill: about 24 g and 37 minutes; the webs are solid either way. Slot 1 is the strip colour, slot 2 the label colour; expect a small pr

Assembly

  1. Set the Layer height and First layer height sliders to your slicer profile, then print the strip flat with no supports.
  2. Let it cool, or for PETG try flexing one row once while it is still warm and the other row cold, and compare the results.
  3. Hold the spine and fold each tab down 90 degrees, then 180 degrees, starting with the thinnest web. Note the layer count where a web whitens, cracks or stays bent.
  4. Repeat the folds and count cycles to failure for each layer count, comparing the short (S) and long (L) rows.
  5. Pull each spring's tab along the strip to feel the 2, 3 and 4 line beams and see which one takes a set.

Good to know

  • The strain figures are an estimate from simple beam bending (fold angle x web thickness / (2 x flex length)) compared with the engine's typical elongation at break: PLA 4%, PETG 10%, TPU 95A 400%. Real webs also bend into their fillets, and thin printed films often stretch past these values, so what
  • G-Flex PETG and other flexible blends are not in the engine's material list, so no limit is computed for them. Print the strip and bend it to find out.
  • Webs are whole layers only if your slicer's layer height and first layer height match the sliders. A strong elephant's foot or a squashed first layer will make the thinnest webs thinner.
  • Nothing here was printed or bend-tested. Cycle counts come only from your own bending.
  • Spring travel figures are at the material's allowable stress (one third of its strength), not where it takes a permanent set.
  • This is a test piece. Don't use these hinges in parts that carry loads or need to be safe.

Comments