From the Loftsmith Workshop

Stereo VU meter case for two GC9A01 round screens and ESP32

Turns two small round screens and an ESP32 into a desktop stereo level meter. The front leans back so the dials face you, and each screen sits in its own round bezel with a small hole below it. Change the screen spacing or the board length to match your parts.

7 parts · 145 g · 136 × 85 × 75 mm

by Loftsmith Workshop

Dark angled box with two round gold-rimmed dial faces on the front and a small port on the side
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • shell · PLA · Face down (bezel side flat on the bed), open back facing up

    136 x 83 x 79 mm as printed, about 87 g and 124 min. No supports. It includes the front ballast block, with four slots opening toward the back, and four 8.4 mm rubber-foot recesses in the floor.

  • bezel ×2 · PLA (accent colour, e.g. brass or gold) · Front face down, centring spigot pointing up

    About 3 g and 8 min each. The round style is 50 mm across; the meter style is 54 x 46 mm.

  • screen-retainer ×2 · PLA · Flat bar on the bed, legs and snap arms pointing up

    About 2 g and 9 min each. Snap arms are 12 mm long and 1.6 mm thick.

  • sled · PLA · Flat, as modelled (end posts and ledges up, T-slot underneath)

    About 17 g and 28 min. Two board bays; the T-slot ceiling is an 8.2 mm bridge.

  • cover · PLA (PETG if you open it often) · Outside (back) face down; lip, snap arms, hold-down shelf and stop plates pointing up

    About 30 g and 48 min. 5 mm rim and 2.4 mm floor with vent slots; the 6.2 mm jack hole sits at floor level.

Print settings

Layer height
0.2 mm
Walls
2 walls (default)
Infill
15 %
Supports
None
Notes
All 7 parts: about 151 g and 4 h 4 min at 2 walls / 15 % infill. With 3 walls / 15 %: about 190 g and 5 h 7 min. Print the bezels in an accent colour and the shell and cover in a dark colour. Each part fits a 180 mm bed at the defaults; the widest setting (90 mm spacing, meter bezels) makes the shel

Hardware

  • 2 × GC9A01 1.28 in round display module (40.4 x 37.5 mm board) · Glass diameter (about 36 mm) and stack height are estimates; the header goes toward the gap at the top of the pocket.
  • ESP32 DevKit board, 30- or 38-pin (48-60 x 25-31 mm) · One board can drive both screens on a shared SPI bus. Add a second board only if your build uses one per channel. Headers point down, with 13 mm under the board. Set the length and width sliders to yo
  • 4 × 8 mm adhesive rubber bumper feet, about 2.5 mm tall · Stick into the 8.4 x 1.0 mm floor recesses; about 1.5 mm stands proud.
  • 68 × Steel ballast: steel shot (BBs) or small steel nuts · Quantity is grams: about 68 g fills the 15 cm³ of slots at the defaults, assuming about 4.5 g/cm³ as poured. Fix it with a little hot glue.
  • 2 × 5 mm LED · Peak lamps. Push in from behind until the flange sits on the boss; a dab of hot glue holds it.
  • Panel-mount 3.5 mm stereo jack, 6 mm thread, with nut · Body assumed about 11 x 11 x 14 mm; mounts through the 2.4 mm cover floor at floor level.
  • USB-C (or micro-USB) cable · The plug enters through the 13.5 x 8.5 mm side opening into the left board's port.
  • Cyanoacrylate glue and hot glue · CA glue for the bezels, hot glue for the ballast and LEDs.
  • Hook-up wire · Screens, LEDs and jack, plus 5 V and GND to the right board if you fit one.

Assembly

  1. Glue the bezels: set each bezel's spigot into its countersunk window from the front and fix it with a few drops of CA glue.
  2. Stick the four 8 mm rubber bumpers into the floor recesses.
  3. Pour about 68 g of steel shot or small steel nuts into the four ballast slots at the front of the floor (they open toward the back) and fix them with a little hot glue.
  4. Fit the peak LEDs from inside: push each 5 mm LED through its 5.1 mm hole until the flange sits on the boss, then add a dab of hot glue.
  5. Drop each GC9A01 module, glass first, into its pocket from behind, header toward the gap at the top. Press a screen-retainer straight down until both arms click over the posts. To remove it, push the arms outward and lift.
  6. Wire the screens, LEDs and jack. With two boards, run 5 V and GND from the left ESP32 to the right one (only the left board gets the USB cable). Program the boards before closing the case.
  7. Set each ESP32 pins-down onto its sled bay, between the end posts and corner guides, with the left board's USB port toward the left end.
  8. Slide the sled in from the back along the floor T-rail until it stops on the rail block.
  9. Put the 3.5 mm jack through the low hole in the cover from inside and tighten its nut on the outside.
  10. Press the cover in until both side catches click flush into their windows. Its shelf now sits 0.2 mm above each ESP32 module, and its stop plates hold the sled. To open: press both catches in through the side windows and pull the cover back, using the fingernail scallop at the bottom seam.
  11. Plug USB-C into the left side opening and your audio lead into the back jack.

Good to know

  • Checked in the Loftsmith engine, not printed. Test-print the bezel spigot fit and both snap catches first.
  • Stability: with about 68 g of steel ballast and the rubber feet it tips back past 11.3 N on the jack lead (6.9 N without ballast). The ballast mass assumes about 4.5 g/cm³ as poured. A firm push when plugging in can still slide it on its feet, so hold the case.
  • The 40.4 x 37.5 mm screen board size is sourced. The 36 mm glass, 2.0 mm glass and 1.6 mm board stack, and the ESP32 module can (25.5 x 18 x 3.2 mm) are estimates; check your parts against the pockets.
  • The retainer legs press the screen board 16 mm either side of centre. Modules with parts there, or with the header on a side edge, may need the legs trimmed.
  • Each ESP32 rests on 3 mm ledges under its ends and is held down by the cover shelf over its module can, with up to 0.2 mm play. It is held only while the cover is on.
  • There are 13 mm under each ESP32: straight Dupont housings on downward pins will not fit, so solder wires or use bent connectors.
  • There is one USB entry, to the left board. A right-hand board needs power from the left one, and the cover must come off to reprogram it.
  • Some edges stay chamfered rather than rounded because they lie on the bed: the face's side edges, the 45 degree lands at the brow and heel, and the cover's back edges. A round there would overhang. For the same reason the cover's back face is flat.
  • The VU dials in the pictures show what the screens display; they are not printed parts.
  • PLA snap strains are 1.26 % and 1.45 %, fine for occasional opening. Print the cover in PETG if you open it often.

Comments