From the Loftsmith Workshop

Newel post basket for 65-95 mm square posts, no screws

A little catch-all for keys, glasses and pocket clutter, hung right on the stair post where you walk past. It wraps around a square post, so there are no screws and no holes in the wood. The basket has two pockets and slots in the front. Set the post width to match yours.

2 parts · 112 g · 130 × 176 × 70 mm

by Loftsmith Workshop

Teal two-pocket basket with slotted front, wrapped around a square wooden post
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • caddy · PETG · Upright as modelled: basket floor and collar band on the bed

    Basket, collar, front pad, hinge pin and latch lip in one body. About 100 g and 2 h 18 min of the total at 2 walls, 15% infill. PETG because the latch lip and hinge pin take repeated loads and PETG is tougher and less brittle than PLA.

  • back gate · PETG · Upright, printed in place on the hinge pin in the same object as the caddy

    Prints already assembled with 0.45 mm round the pin and 0.6 mm at the latch. About 11 g. Keep both bodies as one object (the 3MF does this) so the gaps survive.

Print settings

Layer height
0.2 mm
Walls
2 walls is the page default (about 116 g, 2 h 46 min). 3 walls recommended for a stiffer hinge pin and latch lip (about 159 g, 3 h 47 min at 15% infill).
Infill
15%
Supports
None
Notes
PETG, one object with both bodies (print-in-place). Footprint at the defaults is 130 x 176 mm, so it fits a 180 mm bed. The largest settings (170 mm basket, 75 mm depth, 95 mm post) need 170 x 208 mm. Keep elephant's foot compensation on so the hinge tube does not fuse to the pin on the first layer.

Hardware

  • Self-adhesive felt or thin rubber tape (optional) · For the two inner pads if your post finish is very glossy or you want to avoid marks. If you add tape, increase Pad gap by the tape thickness.

Assembly

  1. Measure your post across the flat faces at the height you want the caddy and set Post width. Leave Pad gap at 0.6 mm unless the post is uneven or you are adding tape to the pads.
  2. After printing, let it cool. Lift the gate's raised tab end about 5 mm and swing the gate open to free the hinge. A gentle twist breaks any first-layer bond at the pin.
  3. With the gate swung open, hold the caddy at the height you want and push it onto the post from the front, so the post goes in through the open back.
  4. Swing the gate shut and let its tooth drop into the slot in the right-hand wall. It now cannot open unless you lift it.
  5. Load the basket. It tips forward slightly (2.5 degrees at the default pad gap) and wedges against the post. To move it, lift the front of the basket to unwedge it, slide it, and let go. You can also slide it down onto the post's base moulding or skirting so it rests there.
  6. To remove it, empty it, lift the gate tab 5 mm, swing the gate open and pull the caddy forward off the post.

Good to know

  • The grip comes from friction and is an estimate: the engine assumes a friction coefficient of 0.25 between PETG and painted or varnished timber. On a very glossy or waxed post it may slide; try a light load first, add felt or rubber tape to the pads, or rest it on the post's moulding.
  • Load is rated at about 1 kg spread in the basket and 0.5 kg on the lead hook (the checks use twice those weights for things being dropped in). Do not pull on it or use it as a handhold.
  • The locking check uses the basket's centre. A single light item pushed hard against the post side of the basket has less leverage and may not lock on its own.
  • It fits square posts only, 65 to 95 mm across the flats. It does not fit turned or round posts.
  • With larger pad gaps the basket tips further forward, up to 6 degrees at 1.5 mm.
  • The basket is never narrower than the collar, so with a 95 mm post a 115 mm Basket width prints at 117 mm.
  • Hinge, latch and fits were checked in the Loftsmith engine as rigid geometry. Print tolerance, wear and how it feels to use still need a real print.

Comments