From the Loftsmith Workshop

Flight sim gauge bezel for GC9A01, 2 1/4 or 3 1/8 in panel

Gives a small round GC9A01 screen a proper instrument-panel face for your home flight sim. A ring of tick marks surrounds the screen, a little hood cuts glare, and a ribbed knob sits off to one side. Change the screen and panel sizes to match your own parts.

3 parts · 24 g · 73 × 73 × 27 mm

by Loftsmith Workshop

Square dark panel with a round tick-marked bezel, a curved glare hood and a ribbed white knob at one corner
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • bezel · PLA, matte black (filament 1) · Rear face down, front face, hood and index marks on top, as modelled

    73 x 73 x 15 mm at the defaults, about 16 g and 26 min (the 3 1/8 in size uses an 82.6 mm square flange). Holds the screen pocket, the encoder pocket, the M4 nut traps and three M3 insert holes. PLA: stiff, and a cockpit panel stays at room temperature.

  • index marks · PLA, white (filament 2) · Printed with the bezel as its top 1.2 mm

    48 raised marks and a ring line, about 1 g. Printed in place on the bezel with an AMS or a manual filament swap. With one filament they come out as raised black marks.

  • back cover · PLA, matte black · Rear face down, pusher ring up, as modelled

    56.8 mm disc at the defaults, about 6 g and 12 min (79.8 mm on the 3 1/8 in size). Its pusher ring holds the screen against the bezel lip, and a top slot passes the screen's header leads.

  • knob · PLA, white · Standing on its base, D-bore opening down, as modelled

    15 mm knurled knob, 15.9 mm tall with a 20 mm shaft, about 2 g and 8 min. Printed whenever the Encoder knob toggle is on and there is room: always on 2 1/4 in, and on 3 1/8 in with modules up to 46.5 mm.

Print settings

Layer height
0.2 mm
Walls
2 walls (page default); 3 walls for stronger walls around the inserts
Infill
15%
Supports
No supports needed. The 2.25 mm screen lip is a short ring overhang, and the 12.8 mm encoder-pocket roof and the nut-trap ceilings bridge. The engine flags 4.0% overhang on the bezel, about 1 g if you add supports.
Notes
Defaults (2 1/4 in, all three parts, two colours) at 2 walls / 15%: about 30 g and 1 h 1 min, including about 6 g and 13 min of filament-change purge for the white marks. At 3 walls / 15%: about 38 g and 1 h 16 min. Fits a 180 mm bed.

Hardware

  • GC9A01 1.28 in round TFT module · Default screen, modelled as a 37.5 mm module with a 32.4 mm visible area (2.55 mm border) and a 4.5 mm stack. Measure yours and set the module, border and thickness sliders.
  • EC11 rotary encoder with push switch, 6 mm D-shaft, M7 x 0.75 bushing · Comes with its M7 nut. Default 20 mm shaft; 15 and 25 mm also work.
  • 4 × M4 pan-head screw · Three on 2 1/4 in with the knob, four otherwise. Length at least panel thickness + 5 mm flange: M4 x 10 for panels up to 5 mm, M4 x 12 for 6 mm.
  • 4 × M4 hex nut · Pressed into the corner traps on the bezel rear (three on 2 1/4 in with the knob).
  • 3 × M3 heat-set insert, 4.1 mm hole x 5.7 mm · Each sits in at least 1.5 mm of wall.
  • 3 × M3 x 8 countersunk screw · Hold the back cover.

Assembly

  1. Heat-set the three M3 inserts into the holes on the bezel rear, then press an M4 nut into each corner trap.
  2. Push the EC11 encoder in from the rear so its bushing comes through the front plate, then tighten its M7 nut. On 2 1/4 in this is the flange corner, and the nut sits in the panel's 12 mm knob hole; on 3 1/8 in it is the face. Snip the encoder's small anti-rotation tab if it stops the body sitting fl
  3. Lay the screen face-down in the round pocket with its header row at 12 o'clock (set the display rotation in software).
  4. Feed the screen leads through the cover's top slot and fasten the cover with three M3 x 8 countersunk screws.
  5. Fit the nose into the panel hole from behind and fasten it with M4 screws from the front through the panel into the captive nuts.
  6. Push the knob onto the D-shaft with the flat lined up. It floats 0.6 mm above the bushing.

Good to know

  • 3 1/8 in uses the published standard: an 80.3 mm (3.16 in) hole with four #18 holes on an 88.9 mm (3.5 in) circle. The nose is 79.8 mm, and a 3 1/8 in hole saw cuts about 79.4 mm, so open the hole up before fitting.
  • 2 1/4 in: the hole is modelled at 57.4 mm, following the source's 'slightly larger than 57.15 mm'; the 56.9 mm nose also fits a plain 57.15 mm hole-saw cut. No datasheet screw pattern was available, so the 70 mm screw circle is this design's own. Use the printed flange as your drilling template.
  • On 2 1/4 in the knob sits in the lower flange corner (7:30, or 4:30 when the Knob position slider is below 6 o'clock). It needs an extra 12 mm hole in the panel, 38 mm from the centre, and uses one of the four screw corners.
  • Screen size limits: 2 1/4 in takes modules up to 39.5 mm, and larger slider values are capped. 3 1/8 in takes up to 62 mm, with the knob inside the face only up to 46.5 mm; above that the knob is left off. Measure your module and its black border.
  • GC9A01 and EC11 sizes are typical values, not measured parts. Fits, clearances and the 30 N knob-press stress were checked in the Loftsmith engine, not on a printed part, so print the bezel first and test-fit.

Comments