From the Loftsmith Workshop

Flipping tippe top with steel-ball ballast, 32-45 mm

A spinning toy that does a trick: give it a good twirl and it flips over to spin on its stem. A steel ball inside shifts the weight, and the body unscrews so you can load it. Change the body width or stem length to tune how it behaves.

2 parts · 12 g · 38 × 38 × 49 mm

by Loftsmith Workshop

Round teal top with a short pale yellow stem and a knob on the end, resting on a flat surface
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • body · PLA · Flat face down (dome up)

    38 x 38 x 32.6 mm at default. No supports: the 45 degree shoulder, the 50 degree internal cones and the V-groove swirl are self-supporting; the 6 mm ball-pocket floor is a short bridge. Contains a sealed internal cavity sized by the script. Print at 100% infill.

  • stem · PLA · Upright, standing on its plug end

    14 x 14 x 37.2 mm at default; 2.5 mm pitch thread with steeper-than-45 degree flanks, no supports. Print at 100% infill. Above about 40 mm tall (large bodies or long extra stem) add a brim.

Print settings

Layer height
0.12-0.16 mm recommended (smaller steps at the rolling pole); 0.2 mm also prints
Walls
Any wall count at 100% infill
Infill
100% for both parts: the balance is computed for solid parts
Supports
None
Notes
The page stats line (2 walls, 15% infill) shows about 12 g and 31 min for both parts at the default size; that setting is not recommended for this toy. At 100% infill the default top uses about 27 g of PLA (21.7 cm3 solid volume); the slicer will show the longer time. Total spinning mass with the st

Hardware

  • 3/8 in (9.525 mm) steel bearing ball · Default ballast, about 3.55 g. Use this or the M6 nut, matching the Ballast setting.
  • M6 hex nut, ISO 4032 (10 mm across flats, 5.2 mm thick) · Alternative ballast, about 2.5 g; only when Ballast is set to M6 nut. Drop it in flat.

Assembly

  1. Print the body and the stem in PLA at 100% infill.
  2. Drop the 3/8 in steel ball (or the M6 nut, lying flat) into the threaded hole in the flat face; it rests on the pocket floor at the bottom.
  3. Screw the stem in, about two turns, until its countersunk collar seats in the face. The stem end then stops 0.2 mm above the ballast so it cannot rattle.
  4. If the bottom of the ball shows layer steps, sand that pole lightly smooth.
  5. Spin it fast by the stem on a hard, smooth table: it tilts, rolls up onto its stem and keeps spinning upside down.

Good to know

  • The flip is computed, not tested: the script checks the rigid-body tippe-top inversion condition (1 - alpha < I1/I3 < 1 + alpha) with a mass model of the solid PLA parts plus the steel ballast. Spin speed, table friction and print accuracy also decide whether it flips, and this design has not been p
  • Print both parts at 100% infill. The balance is computed for solid parts; at low infill the printed mass sits mostly in the outer walls and the ratio moves out of the band.
  • Contains a small steel ball or nut held in by a screw thread: not for small children.
  • Body sizes run from 32 to 45 mm; below 32 mm the computed condition could not be met with these parts.
  • Combining the smallest body with the thickest, longest stem can fall outside the computed band; the 'Flips over' check turns red when it does.
  • From about a 40 mm body, or with the longest extra stem, the stem is a 40-46 mm tall slim upright print; use a brim.
  • The thread clearance (default 0.4 mm) depends on your printer; raise it if the stem binds, lower it if it is loose.

Comments