From the Loftsmith Workshop

Thermostat wall plate to cover old outline, Nest and ecobee

Hides the bare patch and paint ghost left behind when an old thermostat comes off the wall. The plate has a big round hole for the wires and slotted screw holes, so a Nest or ecobee base can sit right on top. Set the old outline size and it covers your mark.

1 part · 43 g · 140 × 6 × 118 mm

by Loftsmith Workshop

Rounded white wall plate with a central wire hole and four slotted screw holes, shown against a green wall
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • plate · PLA · Back face down on the bed, so the bevel and base recess face up. No supports.

    140 x 118 x 5.5 mm at the defaults, about 45 g and 1 h 3 min at 2 walls and 15% infill. PLA because it is stiff, prints flat easily and takes primer and wall paint well. It is an indoor part that carries no load.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
Default figures from the build report: about 45 g and 1 h 3 min at 2 walls/15%. With 3 walls/15% for stiffer slot edges it is about 60 g and 1 h 24 min. Ironing the top surface gives a smoother face to paint. The defaults fit a 180 mm bed. With every size slider at its maximum, the rounded rectangle

Hardware

  • 2 × M4 (or #8) countersunk wood screw, about 30 mm · Fixes the plate to the wall through the horizontal slots on the recess floor. The new base covers them.
  • 2 × Wall anchors to suit the screws · For the plate screws. Reuse the old anchors only if they line up.
  • 2 × Thermostat base screws (supplied with the thermostat, or longer) · These go through the base and the plate's vertical slots into the wall. At the default thickness the plate adds 4.3 mm under the base, so you may need screws that much longer than the supplied ones.

Assembly

  1. Turn the power to the HVAC system off at the breaker before you remove the old thermostat.
  2. Measure the old paint outline (width, height, corner radius) and how far the wire hole sits above or below its centre. Measure the new base's width and the distance between its two screw holes. Enter these on the sliders.
  3. Pull out or cut flush any old anchors that would stop the plate sitting flat. Prime and paint the plate if you want it to match the wall.
  4. Feed the thermostat wires through the 22 mm wire hole and hold the plate level against the wall.
  5. Fix the plate with two countersunk screws through the horizontal slots on the recess floor. The slots allow 2 mm of adjustment either way.
  6. Seat the base in the recess and drive its screws through the vertical slots into the wall anchors. Wire it as the thermostat's instructions say, then fit the thermostat body.

Good to know

  • The body sizes come from the manufacturers' published specs: Nest Learning Thermostat (4th gen) 98 mm across, Nest Thermostat (2020) 84 mm across, ecobee Smart Thermostat Premium 103.89 x 103.89 mm.
  • Only for low-voltage (24 V) thermostats. The plate carries no wiring, and the power must be off at the breaker while you work.
  • Base width and base screw spacing are your own measurements. The defaults (76 mm and 56 mm) are placeholders, not published base sizes. If a check fails for your numbers, for example a base wider than the Nest Thermostat (2020) body, the Check tab says so.
  • The wire hole is a fixed 22 mm. The base screw slots run vertically. If your base's screws are not on a vertical line, drill new holes through the solid recess floor.
  • The fit checks are geometry only and have not been tested in a real print. Print it and hold it against the wall and base before you paint it.
  • PLA softens at about 55 °C. Keep the plate away from heater outlets and direct hot sun.

Comments