From the Loftsmith Workshop
SCD40/SCD41 CO2 monitor case with sealed sensor pod
A small case for an SCD40 or SCD41 CO2 sensor, so your air-quality gadget lives in a tidy box instead of a tangle of wires. The front has a honeycomb grille and a window for the sensor, and slots along the top let air in. Change the sensor board width and height to match your board.
2 parts · 33 g · 87 × 25 × 50 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- case · PLA (PETG if it will sit in sun or near · On its flat back (printRotate -90° about X); no supports
About 24 g and 37 min at 2 walls/15%. Holds the sensor pod, the solid divider, the MCU chamber, the top exhaust slots, the right-side USB opening and the board pads with corner guides. PLA suits a room-temperature desk device; the MCU only warms its own chamber slightly.
- front cover · PLA (PETG if it will sit in sun or near · Face down (printRotate 90° about X); no supports
About 9 g and 17 min at 2 walls/15%. Pill-shaped hex grille for the pod, chamfered screen window, display rails with stops, divider groove and thumb notch. Its dovetail edges and rail lips are 45° overhangs that print without supports.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 walls (figures quoted at 2 walls/15%)
- Infill
- 15%
- Supports
- None
- Notes
- Both parts at 2 walls/15%: about 34 g and 56 min in total (case 24 g / 37 min, cover 9 g / 17 min) at the default sliders. At 3 walls the build report gives about 45 g and 1 h 14 min. The dovetail and divider fits use 0.2 mm clearance per side. If your printer over-extrudes, the cover will slide sti
Hardware
- Double-sided foam tape, about 1 mm thick · Small strips on the pad rails hold the sensor board and the microcontroller in place. The corner guides set their position.
- Reusable putty (e.g. Blu-Tack) or a dab of hot glue · Seals the 14.6 mm² cable gland in the divider around the sensor leads, so the pod stays apart from the MCU chamber.
- SCD40/SCD41 breakout board · Default sliders match a 25.5 x 22.8 x 7.7 mm board (Adafruit size). Set the sensor sliders to your board.
- Wemos D1 mini or ESP32-C3 SuperMini · Pick it with the Microcontroller choice. Its USB port lines up with the opening in the right wall.
- 0.96 in or 1.3 in I2C OLED, or 1.54 in e-paper module · Pick it with the Display choice.
- 2 × 4-wire jumper leads · One set from the sensor to the MCU through the gland, one from the display to the MCU. Single Dupont housings (2.5 mm square) pass the gland one at a time.
- USB lead and 5 V supply · Plugs in through the 14.5 x 9 mm opening in the right wall. Low voltage only.
- 2 × Picture-hanging adhesive strips (optional) · For wall mounting on the flat back.
Assembly
- Put small strips of 1 mm foam tape on the two pad rails in the left pod. Press the SCD40/SCD41 board onto them, sensor facing the front, pushed down into the two bottom corner guides.
- Thread the sensor's four leads through the diamond-shaped gland low at the back of the divider (one Dupont housing at a time), then press a pea of putty into the gland around the leads to seal it.
- Tape the microcontroller onto its pads in the right chamber, components facing the front, pushed against the two left corner guides so its USB port lines up with the opening in the right wall. Connect the sensor leads.
- Slide the display down into the rails on the back of the front cover, glass toward the window, until it rests on the two stops. Connect its leads to the microcontroller.
- Lower the cover into the dovetail grooves from above and slide it down until it sits on the bottom wall. The divider's edge slides into the groove on the back of the cover.
- Plug the USB lead in through the right-side opening. To open the case, push up on the thumb notch under the cover and slide the cover off the top. The display can also be lifted out through the top slot.
Good to know
- This case gives a checked layout (sensor beside and below the MCU, a solid divider, separate vents), not a guarantee of accurate readings. Calibrate the SCD4x as Sensirion describes. The case only measures; it does not protect anyone.
- Module sizes are typical values, not measurements of every seller's board. OLED glass and active-area positions vary between sellers, so check your display against the window before printing the cover.
- The pod is only separate once the cable gland is sealed with putty or glue around the leads.
- Gravity holds the front cover down and the display rests in its rails, so don't carry or hang the case upside down.
- The sensor and MCU boards are held with foam tape on locating pads, not clipped in.
- Checked in the Loftsmith engine only; not yet printed or tested. The slide fit (0.2 mm per side) may need tuning on your printer.
- Low-voltage USB power only.
Comments