From the Loftsmith Workshop
US single-gang wall plate for 86 mm ESP32 touch panels
Gives an 86 mm ESP32 touch panel a proper home on a US single-gang wall box. A raised frame holds the panel, with a square opening behind it for the back of the housing and two small holes for screws. Change the panel size or screw spacing to match yours.
1 part · 41 g · 102 × 10 × 130 mm
Loading the 3D view
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- plate · PLA · Back face (the flat wall side) down on the bed, pocket facing up
102 x 130.3 x 10 mm at defaults. About 42 g and 59 min at 2 walls / 15% infill, the page default. Recommended 3 walls / 15%: about 54 g and 1 h 17 min, which gives the inserts and keyhole lips solid walls. PLA is stiff and easy to print, and indoors on a wall it is well below its 55 °C softening poi
Print settings
- Layer height
- 0.2 mm
- Walls
- 3 recommended (the page stats use 2)
- Infill
- 15%
- Supports
- None
- Notes
- Print back face down. At the page default of 2 walls / 15% it is about 42 g and 59 min. At the recommended 3 walls / 15% it is about 54 g and 1 h 17 min. The keyhole channels and lead groove have short bridged roofs (under 8 mm), which print without supports.
Hardware
- 2 × M3 heat-set insert (about 5.7 mm long, 4.1 mm hole) · Pressed into the pocket floor at the panel's screw spacing (60 mm by default)
- 2 × M3 screw, length to suit the panel's mounting holes · Fix the panel's 86-box mounting holes into the inserts
- 2 × #6-32 pan-head screw, about 1/2 in · Driven into the bracket's plate-screw tabs (3.281 in apart), heads left about 2.2 mm proud to hang the keyholes
- US single-gang low-voltage mounting bracket · Old-work or new-work ring. Not supplied by the print.
Assembly
- Install a US single-gang low-voltage bracket and bring the 5 V lead out through it. Low voltage only: no mains wiring in the same opening.
- Drive the two #6-32 pan-head screws into the bracket's plate-screw tabs. Back each one out until the underside of its head stands about 2.2 mm off the tab (2.0 to 2.6 mm works).
- Press the two M3 heat-set inserts into the holes in the plate's pocket floor with a soldering iron, flush with the floor.
- If you chose the bottom lead exit, press the lead into the groove in the back of the plate first.
- Hang the plate: line its two round keyhole entries up with the screw heads, push it flat against the bracket, then let it drop 9 mm so the heads lock behind the lips.
- Plug the 5 V lead into the panel. Pass the panel's back housing through the window, fix it through its two mounting holes into the inserts with M3 screws, then fit the display face as you would on an 86 box.
Good to know
- Low-voltage only. Use it with the 5 V lead version of these panels. Never use it with panels that have a mains power module, or with mains wiring in the same box or bracket.
- The default back housing (46 x 46 mm, about 24 mm deep) and the panel's 2.5 mm corner radius are estimates. Measure your panel and set the back housing sliders. The housing also has to pass through your bracket's opening.
- Some slider combinations don't fit: a small screw spacing with a wide back housing (for example 56 mm with 50 mm) leaves the inserts breaking into the window, and the 'Panel inserts clear the window' check will fail.
- The plate hangs on the screw heads by gravity. Sliding it up 9 mm lifts it off, so it is not tamper-proof.
- Strength figures are engine estimates (a 50 N pull on the panel's top edge), not test results. Print it and check the fit on your panel before relying on it.
Comments