From the Loftsmith Workshop

Spinning thaumatrope Christmas ornament, star on tree

A little Christmas trick for the tree. Hang it by two string holes, one at the top and one at the bottom, twist the strings, and let it spin so the tree and the star blur into one picture. Change the disc size or hole size to suit your string.

3 parts · 13 g · 60 × 6 × 70 mm

by Loftsmith Workshop

Round dark disc with a raised gold tree, a ring of gold dots and a string hole at top and bottom
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • back-half · PLA (navy) · Mating face down, picture face up

    About 6 g, 13 min at defaults. Includes back-picture (the star, baubles and bead border), printed in gold after a pause at the first layer above 2.0 mm (half the disc thickness).

  • back-picture · PLA (gold), filament 2 · Printed as part of back-half

    Not a separate print: it is the gold top layers of back-half.

  • front-half · PLA (navy) · Mating face down, picture face up

    About 7 g, 13 min at defaults. Includes front-picture (the tree and bead border), printed in gold after a pause at the first layer above 2.0 mm.

  • front-picture · PLA (gold), filament 2 · Printed as part of front-half

    Not a separate print: it is the gold top layers of front-half.

  • key · PLA · Flat

    14 x 6 x 2.2 mm stadium key at defaults, about 4 min. Lines the halves up one way only.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
Default figures from the build report at 2 walls / 15% infill: about 14 g and 31 minutes for both halves and the key. Print each half face up in navy (or any dark colour). Add a pause/filament change at the first layer above half the disc thickness (2.0 mm at the default 4 mm) and finish in gold. Us

Hardware

  • 2 × Thin string or cotton thread, about 1-1.5 mm · About 25-30 cm each, one tied through each ear. The default 2.4 mm hole leaves room for a 1.2 mm string.
  • Glue for PLA (CA glue or similar) · A few drops to fix the key and join the two halves.

Assembly

  1. Print both halves face up, changing to gold at the first layer above half the disc thickness (2.0 mm at defaults). Print the key flat.
  2. Glue the key into the slot on the back half's flat side. The slot is off-centre, so the halves only meet one way round.
  3. Put a few drops of glue on the flat side, press the front half on over the key and line up the ears. Hold or clamp it until the glue sets.
  4. Tie a 25-30 cm string through each ear hole and knot it over the ear tip.
  5. To play: hold one string in each hand with the disc between them, twirl the strings between your fingers (or wind the disc up), then pull the strings taut so the disc flips fast and the star from the back face appears on the tree.
  6. To hang it: use the top string as the hanger; it turns slowly on the tree and shows both pictures.

Good to know

  • How fast it spins and how well the pictures merge depend on the string and how you twirl it; that has not been tested on a real print.
  • Not a toy for young children: it has strings and a small glued-in key.
  • PLA softens around 55 °C. Keep it away from hot incandescent bulbs and fireplaces.
  • The key has 0.2 mm of clearance. If your printer runs tight, sand the key lightly, since it is glued in anyway.
  • Each face has one picture colour (gold on navy). The colour change is a manual pause at a layer, not multicolour printing.
  • At the smallest disc (40 mm), the bird picture has no eye, so every line stays printable.

Comments