From the Loftsmith Workshop

Window candle sill clamp holder for 15-45 mm thick sills

Gives a window candle a steady spot on the sill without any glue or screws. It clamps onto the edge of the sill, and the octagonal cup with low walls holds the candle base. Set your sill thickness and candle width and it fits.

2 parts · 33 g · 65 × 65 × 64 mm

by Loftsmith Workshop

Green octagonal candle cup on a clamp that grips the edge of a tan window sill
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • holder · PETG · On its side, the flat side face down (printRotate 90, 0, 0)

    About 31 g and 49 min at 2 walls/15%. Lying on its side, the clamp bends along its layers and every downward facet is steeper than 45°, so no supports are needed. The threaded hole runs sideways in this orientation (the only overhang, 0.6% of the surface). PETG because sills in the sun get warmer th

  • thumb-screw · PETG · Knob down, shank up (as modelled)

    About 2 g and 9 min. 10 mm thread with a 3 mm pitch and flanks 50° from horizontal, so the thread prints upright without drooping. Fluted 20 mm knob.

Print settings

Layer height
0.2 mm
Walls
2 (3 walls for a firmer thread: about 44 g, 1 h 19 min for both parts)
Infill
15%
Supports
None
Notes
At 2 walls and 15% infill both parts together come to about 34 g and 1 h 0 min (holder about 31 g / 49 min, screw about 2 g / 9 min) at the default sizes. Use PETG, not PLA: a sunny sill can soften PLA. If the screw is tight in the sideways-printed jaw thread, raise the Thread play slider by 0.1 mm

Hardware

  • Small self-adhesive felt pad, about 8-10 mm round (optional) · Stick it under the sill where the screw tip presses, so the tip doesn't mark painted wood. No screws, nuts or inserts are needed.

Assembly

  1. Measure your sill: its thickness at the front edge, and its depth from the front edge back to the window frame. Measure the diameter of your candle's base. Set the sliders to match.
  2. Thread the thumb screw into the jaw from below, knob down, and back it off until the tip is below the top of the jaw.
  3. Slide the holder onto the sill from the room side until its inner corner sits on the front edge of the sill. The cup rests on top and the jaw goes under the sill nose.
  4. Turn the knob clockwise (seen from below) until the screw tip meets the underside of the sill, then give it a light finger twist. Don't crank it.
  5. Set the candle base in the cup and lead its cord out through the notch on the side.
  6. To take it down, lift the candle out, turn the knob anticlockwise two or three turns and slide the holder off.

Good to know

  • For LED or electric window candles only. Never use it with a real flame.
  • It needs a sill with a nose that sticks out over the trim below. The jaw and knob reach 20 mm behind the sill's front edge, so it won't fit flush, tiled or plaster sills with nothing to hook under.
  • Round candle bases only, 40-80 mm across. Square or oval bases won't fit the cup.
  • The tip-over angles assume the candle's centre of mass is at 35% of its height. The screw check assumes a 300 g candle. A top-heavy or heavier candle tips sooner. Before trusting it near curtains or pets, test yours by tilting it gently.
  • The inner corner has a 2.5 mm round to suit eased or rounded sill edges. On a sharp square edge the holder sits less than 1 mm high, and the screw still clamps it.
  • The thread is checked as geometry with 0.45 mm play per side. It has not been printed. If your printer's sideways holes come out small, raise the Thread play slider.
  • The screw tip can mark a painted sill. A small felt pad prevents that.
  • Don't hang or stand anything heavier than the candle on it.

Comments