From the Loftsmith Workshop
Christmas street book nook for fairy lights, sized to shelf
A tiny snowy street that tucks between two books and glows when you thread a string of fairy lights through it. The ceiling is dotted with star cutouts, and the floor looks like cobblestones. Set the gap width and the spacing between your LEDs.
5 parts · 224 g · 75 × 140 × 160 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- base · PLA, dark green · Upside down, cobbled street face on the bed
75 x 140 x 23.5 mm, about 51 g, 73 min. Open underneath: the 2xAA box slides in through the front opening between two guide ribs and stands on the shelf.
- wall-left · PLA, cream or white (it must let light t · Flat, wire-groove side down, house fronts up
136.5 x 135 x 11.8 mm, about 59 g, 82 min. Each lit window has a 0.9 mm skin that glows when the LED behind it is on.
- wall-right · PLA, cream or white · Flat, wire-groove side down, house fronts up
About 60 g, 83 min. Same windows as the left wall, different rooflines.
- back · PLA, cream or white · Flat, groove side down, tree up
61 x 136.5 x 8.3 mm, about 24 g, 36 min. The star on top of the tree is lit by one LED.
- lid · PLA, dark green · Top face down
75 x 140 x 4.5 mm, about 30 g, 43 min. The star-shaped openings let you look down into the street.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- About 232 g and 5 h 28 min for all five parts at 2 walls and 15% infill (engine estimate). Print the two walls and the back in cream or white PLA so the window skins glow, and the base and lid in a dark colour. No AMS is needed because each part is a single colour. The only overhangs are short bridg
Hardware
- Battery fairy-light string (copper-wire micro-LED type) · Measure the LED spacing and set it on the LED spacing slider. At the default size it uses 11 LEDs in a row after the first lit one; any extra LEDs can be tucked into the base. The LED beads must fit a
- 2xAA battery box with switch, about 34.2 x 76.8 x 19.2 mm · Usually comes with the string. It sits in the base with the switch facing the front opening.
- 2 × AA batteries
- Clear tape or a few dots of glue · Optional. Holds the wire in its groove while you assemble; the books on either side also press it in.
Assembly
- Slide the 2xAA box into the base through the front opening, switch facing out. Run its lead back through the hollow and up through the small hole at the front of the left wall slot.
- Press the left wall's tongue into its slot in the base. Lay the wire into the groove on the wall's outer face, starting with the first LED behind the front window. Follow the groove's U-shaped loops so each next LED sits behind the next window. A strip of tape helps.
- At the back corner, wrap the wire through the notch and slide the back panel into its slot. Continue the wire across the back groove so one LED sits behind the star.
- Stand the right wall in its slot and carry on along its groove from the back window to the front. Push the rest of the string down through the right-hand hole into the base.
- Drop the lid on so its slots catch both walls and the back panel. For a permanent build, add a dot of glue at the tongues. Otherwise it lifts off for servicing.
- Switch on through the front opening and slide the nook between your books.
Good to know
- Made for copper-wire micro-LED strings with beads up to about 2.4 mm. Strings with larger bulbs won't fit the groove.
- Measure your string's LED spacing carefully: measure across 10 LEDs and divide by 10. Each window is placed by that number, and spacing on real strings varies by a few millimetres. The 2.6 mm groove gives a little room to nudge each LED into place.
- Depending on the size and spacing, a few LEDs (2 at the defaults) sit in hidden loops on the outer faces and glow against the neighbouring books. Cover them with tape if the glow shows.
- At the default size the battery lead needs to reach roughly 17 cm from the box to the first window. That figure comes from the modelled route, not a measured string.
- The windows glow through 0.9 mm of plastic, which works with white or cream PLA. Dark filament will block most of the light.
- Battery boxes vary. This one is sized for 34.2 x 76.8 x 19.2 mm with 1.8 mm of side play and 0.8 mm of headroom.
- Fit, clearances and the LED positions were checked as geometry in the Loftsmith engine. The model has not been printed or lit.
Comments