From the Loftsmith Workshop
Kindle / Kobo wall frame for Home Assistant dashboards
Turns an old e-reader into a little wall display for your Home Assistant dashboard. The reader sits in a ridged-edge frame with a dark back plate, and there's a notch at the bottom for the USB lead. Change the reader's width, height and thickness to fit yours.
2 parts · 74 g · 124 × 19 × 203 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- frame · PLA (warm sand colour in the render) · Face down: the front lip on the bed, open back facing up
124.2 x 202.5 x 19.2 mm at the default sizes; about 42 g and 61 min at 2 walls/15%. Reeded sides, 45 degree mat bevel round the window, plug bay in the chin, lead slot in the bottom edge, a latch recess and a 1.8 mm paperclip release hole on each side. Overhang 2.2 %, no supports.
- back plate · PLA (charcoal in the render) · Keyhole side (wall side) on the bed
119.8 x 195.3 x 5.9 mm at the default sizes; about 32 g and 46 min at 2 walls/15%. Two hidden keyholes in bosses that the reader rests on, two lower pads, two 37 mm in-plane latch arms with 45 degree lead-ins, chamfered lightening windows.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 walls (the page default): about 77 g and 1 h 51 min for both parts. 3 walls gives a stiffer frame: about 96 g and 2 h 17 min.
- Infill
- 15%
- Supports
- None
- Notes
- PLA, both parts on a Bambu A1 or any bed of at least 256 mm. At the defaults the frame is 202.5 mm tall, so it does not fit a 180 mm bed such as the A1 mini. The frame prints lip-down, so its front face takes the finish of your build plate.
Hardware
- 2 × Wall screw, about 4 mm pan head · Head 7-8.5 mm across and no more than 2.5 mm tall, shank no more than 4.5 mm. Use wall plugs to suit your wall. Leave the underside of each head about 3.8 mm out from the wall. At the default sizes th
- USB cable for your reader (micro-USB or USB-C) · Plug body up to 12 x 7.5 mm, set its length on the USB plug body length slider (12-32 mm). Lead 3-5 mm thick, set on the USB lead diameter slider.
- USB power adapter · For permanent power; not part of the print.
- Paperclip · Only needed to release the back plate.
Assembly
- Measure your reader with calipers: width, height, thickness, and the narrowest distance from its outer edge to the start of the active screen area. Set the four Reader sliders from these. A Kindle Paperwhite 11th gen is 174.2 x 124.6 x 8.1 mm.
- Set up the dashboard software on the reader first, following a current guide for your model and firmware. This frame does not cover that step.
- Plug the USB cable into the reader. Lay the frame face down on a soft cloth and drop the reader in face down. The plug passes through the gap in the stop rib into the chin bay.
- Press the lead into the slot in the frame's bottom edge from the back.
- Press the back plate in, keyhole side facing you, until both side latches click past the catch band.
- Fit two screws level on the wall, 65.5 mm apart at the default sizes, with the underside of each head about 3.8 mm out from the wall.
- Hang the frame: put the round ends of the keyholes over the screw heads, push it flat to the wall and let it slide down 10 mm. The lead runs down the wall from the centre of the bottom edge.
- To take the reader out: lift the frame 10 mm and pull it off the wall. Push a paperclip into the small hole on one side of the frame to free that latch and lift that edge of the plate, then do the same on the other side.
Good to know
- The fit depends on your measurements. Clearance is 0.4 mm per side and 0.3 mm front to back, so a reader in a case or with sizes off by more than that will not fit.
- No screen-border sizes are built in for specific models. Measure the narrowest border yourself; the lip-off-screen check is only as good as that number.
- It assumes the charging port is on the reader's bottom edge, within 25 mm of the centre, and that the plug body is no larger than 12 x 7.5 mm. A reader with its port on the top or a side would have to hang upside down or will not suit this frame.
- The lead leaves straight down from the bottom edge and runs visibly down the wall. There is no in-wall routing.
- At the defaults the frame is 202.5 mm tall, so it needs a 256 mm bed. The largest settings make it 223.5 mm tall.
- The keyhole check assumes a reader of up to 250 g. The frame is not meant to carry anything else.
- PLA softens at about 55 °C. Do not hang it over a radiator or in direct sun.
- The snap strain, keyhole load and fits are engine calculations from typical PLA properties. The latch feel, the paperclip release and the fit to your reader have not been printed or tested.
Comments