From the Loftsmith Workshop

Quilting template with seam allowance: HST, QST, square, hex

A flat template for cutting quilt pieces without doing the seam allowance maths each time. The triangle has a knob to hold it down, and its edges are marked with the cut size and trim lines. Change the finished size to match your block.

2 parts · 16 g · 102 × 128 × 13 mm

by Loftsmith Workshop

Flat teal triangle template with a round knob and dashed cut lines, beside a short 4 in scale check strip
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • template · PLA (teal, filament 1) · Flat, label side up, as modelled. QST templates print rotated 45 degrees so the two short edges run along the bed axes.

    Default 3 in finished HST with a 1/4 in seam: 98.4 x 98.4 mm, 2 mm plate, knob 11 mm tall. About 12 g and 21 min. PLA because it gives stiff, accurate edges; keep it away from the iron.

  • labels · PLA (cream, filament 2) · Printed in place on top of the template (same object)

    5 mm capitals raised 1 mm (CUT 3 7/8, FIN 3 / TRIM 3 1/2, HST 1/4 IN SEAM) plus the dashed stitch line. They start exactly at the plate top, so a single-nozzle printer needs one filament swap at that layer. Printing all one colour also works.

  • check-bar · PLA (teal, filament 1) · Flat

    101.6 mm (4 in) long, 18 mm wide, with ticks every 1/2 in. About 4 g and 10 min. Optional: choose 100 mm or none.

  • bar-marks · PLA (cream, filament 2) · Printed in place on top of the check bar

    Raised tick marks and the 4 IN SCALE CHECK label.

Print settings

Layer height
0.2 mm
Walls
2 walls (page default); 3 walls if you want stiffer edges
Infill
15%
Supports
None
Notes
At 2 walls and 15% infill, the template plus the 4 in check bar is about 20 g and 39 min, including about 3 g of purge for the colour change. At 3 walls and 15% it is about 22 g and 43 min. For two colours on a single-nozzle printer, add a filament change (pause) at the first layer above the plate t

Hardware

  • 0 × None required · Optional: a few adhesive sandpaper or silicone dots on the underside to stop the template sliding on fabric.

Assembly

  1. Print the check bar first or alongside. Measure it end to end with a ruler or calipers: it should read exactly 4 in (101.6 mm) or 100 mm. If it is off by more than about 0.5 mm, fix your printer's XY scale before trusting the template.
  2. Lay the template label side up on the wrong side of the fabric, with the edge marked CUT on the straight grain. For HSTs the two short legs go on the grain; for QSTs the long edge does.
  3. Hold it down by the knob, trace around the outer edge with a fabric pencil, and cut on the line with scissors.
  4. For hand piecing or English paper piecing, use the fussy-cut window version and trace inside the window to mark the sewing line. You can also centre a motif in the window before tracing the outer edge.
  5. The HST template is half of a square cut at the CUT size, and the QST template is a quarter of one. So for the two-at-a-time and four-at-a-time methods you can also cut squares at the labelled CUT size and trim the units to the TRIM size.

Good to know

  • Use it for tracing and scissor cutting only. Do not run a rotary cutter along it: the blade will shave the plastic and change the size.
  • PLA softens around 55 C. Keep the template away from the iron and the ironing board, and out of a hot car.
  • Cut sizes use the standard rule for a 1/4 in seam: HST = finished + 7/8 in, QST = finished + 1 1/4 in. The exact geometric additions computed in the engine are + 0.854 in (HST) and + 1.207 in (QST), so the templates carry about 0.5 mm (HST) and 1.1 mm (QST) of trimming margin.
  • For 3/8 and 1/2 in seams, the HST and QST additions are the same rules scaled to the seam (3.5 x and 5 x the seam). The engine reports the exact geometric value and the resulting trimming margin for every setting.
  • Labels are rounded to the nearest 1/16 in, and the hexagon across-flats label is in decimal inches. On small templates the wording shortens to the bare numbers (a 1 in finished HST reads 1 7/8, FIN 1, HST). An edge with no room carries no label: the 1 in square has no SQUARE label, and the default Q
  • Accuracy depends on your printer's XY scale and first layer; the check bar is there to catch a scale error.
  • The knob only appears on the solid template. With the fussy-cut window on, the frame is the seam allowance itself and has no room for a knob.
  • Default sizes fit a 180 mm bed. Large settings need a 256 mm bed: an 8 in HST is 225 mm (248 mm with a 1/2 in seam), an 8 in QST with a 1/2 in seam prints rotated at 189 mm square, and a 3 in hexagon with a 1/2 in seam is 182 mm wide.
  • The engine checks geometry and dimensions only; no part of this design has been printed or tested on fabric.

Comments