From the Loftsmith Workshop
Table leaf alignment pins and sleeves, 4.5-12 mm holes
Lines up a table leaf with the tabletop so the surfaces meet flush when you drop it in. A small ribbed pin glues into the table edge, and a hole gauge with numbered pegs helps you find your drill size first. Set the hole size to match yours.
9 parts · 21 g · 117 × 92 × 17 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- pin ×4 · PETG · Lying on its side on the long flat, so the layers run along the pin
8.3 x 25 x 7.6 mm at the defaults, about 1 g and 6 min each. PETG because it is tougher than PLA and bends rather than snapping when the leaf is levered on the pins.
- sleeve ×4 · PETG · Standing on its square inner end, mouth up
12.3 mm across x 14 mm long at the defaults, about 1 g and 7 min each. Only needed when the leaf-side hole is oversized or the old brass sleeve is lost; turn the Sleeve toggle off for plain holes.
- hole gauge · PETG · Flat, pegs up
116.8 x 38 x 8.2 mm, about 13 g and 22 min. Pegs from 4 to 12 mm in 0.5 mm steps; the whole-mm row is numbered and each half-mm peg sits between its neighbours.
Print settings
- Layer height
- 0.16-0.2 mm
- Walls
- 2 walls (page default); 4 walls recommended for the pins and sleeves so they print solid
- Infill
- 15% (page default); 25% with 4 walls
- Supports
- None
- Notes
- Default figures for the whole set (4 pins, 4 sleeves, gauge) are about 21 g and 1 h 14 min at 2 walls and 15% infill. At the recommended 4 walls and 25% infill the set is about 30 g and 1 h 41 min. A brim helps the small pins stay down on the bed. If you only need pins, turn the gauge and sleeves of
Hardware
- Wood glue (PVA) or 2-part epoxy · A few drops per pin, on the ribbed end only. Epoxy bonds PETG better than PVA.
- Drill bit at the sleeve size · Only if you use sleeves in a plain leaf hole: the sleeve needs a hole of hole diameter + 2 x sleeve wall (12 mm at the defaults).
Assembly
- Print the gauge first. Push its pegs into the table hole: the largest peg that slides in fully is your hole size. If both 7.5 and 8 feel close, the hole is probably an inch size: 3/16 in = 4.8 mm, 1/4 in = 6.4 mm, 5/16 in = 7.9 mm, 3/8 in = 9.5 mm.
- Set Hole diameter to that size, and set Glued depth and Pin sticks out to the depths of the table hole and the leaf hole (each hole should be at least 1-2 mm deeper than its end of the pin).
- Print the pins lying on their flat and the sleeves standing mouth up.
- Dry fit first: the ribbed end should press into the table hole with firm hand pressure, and the bullet end should slide into the leaf hole or sleeve freely.
- Put glue in the table hole, press each pin in with the ribbed end first, flat facing sideways (toward the next pin, not up or down), until the ribs are all inside the edge.
- For sleeves: glue each one into the leaf hole with its square end first and the countersunk mouth flush with the leaf edge.
- Let the glue cure for the time on the bottle before you slide the leaf on.
Good to know
- The pins line the leaf up; they do not hold it on. The strength check covers a 3 kg sideways shove shared by two pins with a x2 bump factor. Do not lift or lever the leaf by the pins, especially at hole sizes under 6 mm.
- Fits are checked in the engine, not on a printed part. Printed sizes vary by printer: if the ribbed end is too tight or the nose binds, change Rib grip or Running clearance and reprint one pin to test.
- The 0.4 mm flat that the pin prints on adds that much play toward the flat side. Glue the pin with the flat facing sideways so the leaf tops stay flush.
- The gauge reads in 0.5 mm steps. Printed peg sizes can be off by about 0.1 mm, so an inch hole can sit between two pegs.
- Hole sizes from 4.5 to 12 mm only. For vintage 3/16 in pins, a brass or steel pin is stronger than any printed one.
Comments