From the Loftsmith Workshop

Chladni plate stand for 4-8 in speakers with sand tray

Turns a spare speaker into a little sand-pattern show. The square plate sits in a raised tray, so loose sand stays put while it dances into shapes. A small control box with a knob and a wave screen sits beside it. Set it up for your own speaker size.

6 parts · 247 g · 175 × 259 × 94 mm

by Loftsmith Workshop

Square plate in a yellow sand tray on a dark round stand, with a small control box and knob beside it
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • cradle · PETG · Upright, flared foot on the bed

    About 88 g and 123 min at 2 walls/15%. 155 mm across the foot at the defaults. The speaker flange sits on the top ring, three posts carry the tray, and three arches vent the magnet and let the speaker lead out. Press M3 heat-set inserts into the post tops.

  • tray · PETG · Floor down

    About 94 g and 124 min. 175 mm square with a 16 mm rim and a 12 mm chimney around the bolt so sand cannot reach the cone. If the tray is larger than your bed it prints as 2 or 4 pieces (tray-left/right/front/back) joined at raised floor ribs with 1.75 mm filament dowels.

  • hub · PETG · Top face down (as rotated)

    About 6 g and 13 min. The underside follows the dust-cap dome and cone with a 0.3 mm glue gap. A hex pocket holds the bolt head (or a nut on threaded rod). PETG because it sits next to the voice coil.

  • knob · PETG · Flat end down, D-shaft bore facing up

    About 2 g and 8 min. 20 mm fluted knob for a 6 mm D-shaft EC11 encoder.

  • console · PETG · Sloped face down on the bed

    About 41 g and 61 min. A 116 x 70 mm sloped console with an OLED window, encoder hole, side USB slot, rear speaker-lead hole and four corner bosses for M3 inserts.

  • console-base · PETG · Flat, ribs up

    About 17 g and 26 min. Two ribs carry the ESP32 between its pin rows, with zip-tie slots for the ESP32 and the amplifier.

Print settings

Layer height
0.2 mm
Walls
2 walls (page default); 3 walls recommended
Infill
15%
Supports
None
Notes
PETG for every part: the hub sits next to the warm voice coil and the parts take vibration. At 2 walls/15% the whole set is about 256 g and 6 h 8 min on an A1. At the recommended 3 walls/15% it is about 346 g and 8 h 16 min, which gives the M3 inserts more to bite into. You can print the hub solid;

Hardware

  • Speaker, 4 to 8 in · Enter its basket (flange) outside diameter, its mounting depth (flange underside to magnet back) and its dust cap diameter. The cradle seat needs about 7 mm of flat flange. Basket diameter is limited
  • Square metal plate, 1.5 mm aluminium (or thin steel), 120-240 mm · Drill a centre hole for the bolt (6.5 mm for M6, 5.5 mm for M5). Set its size on the Plate size slider.
  • M6 hex-head bolt, about 60 mm (or M5 with the M5 option) · At the default sizes the shank runs 54 mm from the hub to 3 mm above the top nut. Threaded rod with a nut in the hub pocket works too: lock that nut with thread-locker.
  • 2 × M6 nuts and washers · One nut and washer under the plate and one pair on top. Use M5 parts with the M5 option.
  • 7 × M3 heat-set inserts (5.7 mm long) · 3 in the cradle posts and 4 in the console bosses.
  • 3 × M3 x 10 countersunk screws · Tray to cradle posts.
  • 4 × M3 x 6 countersunk screws · Console base to console.
  • 4 × M2 x 6 self-tapping screws · OLED module to its four posts.
  • 4 × Screws for the speaker flange · Short self-tapping screws through the speaker's own mounting holes into the cradle ring (drill pilots). A bead of silicone also works.
  • ESP32 devkit (about 55 x 28 mm) · Your own firmware is needed (none is included).
  • Small low-voltage class-D amplifier board, up to 40 x 30 x 12 mm · Either an analog-input board fed from an ESP32 DAC pin, or an I2S amplifier board. Its rated load impedance must suit your speaker (usually 4 or 8 ohm).
  • 5 V USB power supply for the ESP32 · Enters through the side slot. If a 5 V amplifier runs from the same rail, use a supply with enough current for both.
  • Separate low-voltage DC supply for the amplifier (optional) · Only if your amplifier board needs more than the 5 V USB rail (for example a 12 V board). Its lead shares the rear hole with the speaker wire.
  • SSD1306/SH1106 I2C OLED, 0.96 in (27.3 x 27.3 mm) or 1.3 in (35.4 x 33.5 mm)
  • EC11 rotary encoder with 6 mm D-shaft and panel nut
  • 3 × Small zip ties (up to 4 mm wide)
  • 2-core speaker wire, about 4 mm, and hook-up wire · Speaker wire runs from the speaker terminals out of the front arch into the console's rear hole. Hook-up wire is for the ESP32, OLED, encoder and amplifier.
  • Epoxy or gel CA glue · Hub to dust cap and cone.
  • Fine dry sand · Use sand rather than salt: salt corrodes steel plates and the speaker.
  • 8 × 1.75 mm filament, 12 mm lengths · Only when the tray is split for your bed: 4 dowels per seam.

Assembly

  1. Press three M3 heat-set inserts into the cradle post tops and four into the console's corner bosses.
  2. Set the speaker face-up on the cradle ring between the three posts and run its lead out through the front arch. Drill pilots through the flange's own mounting holes and screw it down (or bed it in silicone).
  3. Drop the bolt head (or a thread-locked nut on threaded rod) into the hub's hex pocket, bolt pointing up. Glue the hub centred over the dust cap with epoxy or gel CA and let it cure.
  4. Lower the tray over the bolt so the bolt passes through the chimney, then fix it to the posts with three M3 x 10 countersunk screws. If your tray printed in pieces, glue the seams first with filament dowels in the rib holes.
  5. Thread a nut and washer onto the bolt, add the plate, then a washer and the top nut. Tighten, and keep the plate level and clear of the chimney.
  6. Console: fit the OLED from inside with its glass in the window and four M2 screws. Push the encoder through the face hole and fit its nut. Zip-tie the ESP32 onto the ribs and the amplifier into its slots.
  7. Wiring: connect the ESP32's tone output to the amplifier input and join their grounds. The tone output is a DAC pin into an analog-input amplifier (add a coupling capacitor if the board needs one), or the I2S pins into an I2S amplifier board. Power a small 5 V amplifier from the ESP32's 5 V (USB) pi
  8. Screw the base into the console with four M3 countersunk screws and press the knob onto the encoder shaft.
  9. Load your tone sketch, sprinkle fine dry sand on the plate and sweep the frequency with the knob.

Good to know

  • No firmware is included. You need your own ESP32 sketch that outputs a sine or square tone (for example from a DAC pin or over I2S) at the frequency set by the encoder and shows that frequency on the OLED. The printed parts hold the electronics; they do not make them work.
  • Size the amplifier to your speaker: its rated load impedance must match the speaker (usually 4 or 8 ohm), and its power should stay within the speaker's rating. A 5 V board running from the USB rail gives only a few watts, so a larger driver or a heavy steel plate may need a higher-voltage board on
  • The Speaker basket diameter slider stops at 210 mm. Some 8 in drivers have frames wider than that; measure the flange before printing. A wider cradle would not fit a 256 mm bed.
  • The speaker shape is modelled from typical proportions: cone depth 17% of the basket, dust cap dome height 22% of its diameter. Real cones vary, so check the hub against your speaker and fill any gap with epoxy.
  • The OLED screw posts assume holes 2 mm in from each module corner and a centred display area. Check your module before printing.
  • There is no slot for the EC11's small locating tab. Snip it off or rely on the panel nut.
  • The load checks assume a 1.5 mm aluminium plate moving 0.5 mm at 150 Hz. Steel plates are heavier and larger strokes load the hub and cone more. None of this has been tested on a printed stand.
  • Use a low-voltage amplifier only and don't overdrive the speaker. Which frequencies make which patterns depends on your plate; nothing here predicts them.
  • Use fine dry sand, not salt (salt corrodes). Sand that jumps hard can still leave the tray at a 10 mm margin; raise the Tray margin slider if it does.
  • When the tray is larger than your bed it is split into 2 or 4 glued pieces with a raised rib along each seam. Seal the seams well so sand cannot leak through.

Comments