From the Loftsmith Workshop
Print-in-place seam gauge with step lock, 6 in or 150 mm
A little sliding ruler for checking hems and seam allowances while you sew. The orange slider glides along the numbered rail and stays put at the step you set. It prints already assembled, so there's nothing to put together.
3 parts · 11 g · 176 × 38 × 10 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- rail · PLA · Flat, marks up, as modelled
175.8 x 16 x 6 mm at the defaults, about 9 g and 16 min. Dovetail sides; round-ended ticks 1.0 mm wide and raised 1.0 mm; 6 mm bold numbers; square lock slots with 0.3 mm lead-in chamfers along the front edge. PLA because it is stiff, easy to print, and the gauge carries no real load.
- marker · PLA · Flat, printed in place around the rail (one object with the rail and bolt)
18 x 32.7 x 9.5 mm, about 2 g. Its square front face is the reading edge, and a raised arrow on top points at it. The pointer fin lies on the fabric. The flat top bridges over the rail.
- lock bolt · PLA · Flat, printed in place inside the marker's front wall
9 x 13.7 x 6 mm, under 1 g. Pull the tab out to slide the marker, push it in to lock. Held in only by friction (no detent).
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- About 11 g and 29 minutes at 2 walls and 15% infill (build report default). 3 walls is about 15 g and 37 minutes. Print the 3MF as one object: it keeps the rail, marker and bolt as separate bodies with their gaps. The engine's overhang warning on the marker (338 mm² at the defaults) is all downward-
Assembly
- Print flat as one object with no supports. The marker and lock bolt print in place on the rail; there is nothing to assemble.
- Once it has cooled, pull the bolt tab out and slide the marker gently from one end to the other a few times to free the print-in-place gaps. Push and pull the tab a few times as well.
- To set a size, pull the tab out, slide the marker until its square front face (the arrow on top points at it) sits at the depth you want, then push the tab fully in so the tooth drops into the nearest slot (every 1/8 in or 5 mm on the fine setting).
- Before pressing, check that the tab is pushed fully in. Then lay the gauge's square tip at the fold and turn the fabric up to the marker's front face.
Good to know
- The lock bolt has no detent and is held only by friction in its chamber (0.4 mm gap at the default setting). Push it fully in after setting a size and check it before pressing. If the bolt drifts back out, the marker unlocks.
- With the bolt fully in, the engine's stress check shows the lock teeth carrying a 5 N push (about half a kilogram) along the rail within PLA's allowable stress. That is a calculation, not a tested result.
- The most likely way for the print to fail is sag in the marker's 17 mm bridged top fusing it to the rail across the print-in-place gap; the model leaves 0.7 mm of clearance above the raised marks at the default gap. If the marker is fused after printing, reprint with the gap slider at 0.45 to 0.5 mm
- PLA softens at about 55 °C. Keep the gauge away from the iron's soleplate and don't leave it under a hot iron. If you will press directly over it, print in PETG.
- Each step has up to ±0.4 mm of play along the rail at the default gap (± the gap setting), so it is a sewing gauge, not a precision rule.
- Check the printed scale against a real ruler before trusting it, because printer or slicer scaling errors show up directly in the marks.
- Steps finer than 1/8 in or 5 mm (for example 1 or 2 mm) aren't offered, because slots and teeth that small would be under about 1 mm wide.
- The 8 in and 200 mm versions need a 256 mm bed: their rails are 226.6 mm and 223.4 mm long, from engine builds at those settings. The 4 in, 6 in, 100 mm and 150 mm rails are 125.0, 175.8, 123.4 and 173.4 mm long.
Comments