From the Loftsmith Workshop

Gingerbread house corner clips and roof props, 4-10 mm walls

Holds a gingerbread house together while the icing sets, so the walls stay put and the roof stops sliding. Four red corner clips grip the baked panels, and two pairs of white props keep the roof panels leaning at the right angle. Set the wall thickness to match your gingerbread.

8 parts · 67 g · 167 × 66 × 119 mm

by Loftsmith Workshop

Gingerbread house with red corner clips on the walls and white props holding up one roof panel
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • corner-clip ×2 · PETG · Upright as modelled, open slots facing down on the bed; the slot ceilings are peaked at about 50° so no support is needed

    About 8 g and 19 min each at 2 walls/15%. 27 × 32 × 51 mm at the defaults. The arm with the sloped top and the heart goes on the gable (pointed) wall.

  • corner-clip-mirrored ×2 · PETG · Upright as modelled, open slots facing down on the bed

    Mirror image of corner-clip for the other two corners. About 8 g and 19 min each.

  • roof-prop ×4 · PETG · Lying on its side (flat face down) so the layers run along the legs

    About 9 g and 16 min each at 2 walls/15%. 42 × 85 × 14 mm at the defaults; height follows the wall height, pitch and overhang sliders. Two per roof panel.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
PETG because it is tougher than PLA and wipes clean. The set of 4 clips and 4 props is about 69 g and 2 h 27 min at 2 walls/15% (the build report's default figures). If you want stiffer clips, 3 walls/15% comes to about 94 g and 3 h 22 min. All eight parts fit together on a 180 mm bed.

Assembly

  1. Set the Baked wall thickness slider to the thickest part of your baked walls, and the Roof pitch, Side wall height and Overhang sliders to the pieces you cut.
  2. Ice the bottom edges, then stand the first two walls at a corner. Lower a clip straight down over their tops: the arm with the sloped top and the heart goes over the gable (pointed) wall, the flat arm over the side wall.
  3. Put the other clips on the remaining corners. Use the mirrored clips on the two corners where the plain one would face the wrong way.
  4. Leave the walls until the icing has set, then lift each clip straight up.
  5. Ice the wall tops and set the roof panels on. Slide two props under each eave from the outside so the lip catches the panel's lower edge.
  6. When the ridge and roof icing have set, slide the props straight out away from the house.

Good to know

  • Not certified food-safe: PETG filament and 3D-printed parts are not certified for food contact. Wash the parts and keep contact short. The clips and props only touch the outside surfaces while the icing sets.
  • Baked gingerbread is uneven. If a wall will not go into a slot, raise the Slot clearance slider (up to 1.5 mm, which lets the walls lean up to 3.9°) or set the wall thickness to your thickest spot.
  • Keep icing out of the top 22 mm of each corner, or wipe it off before fitting a clip, or the clip may stick when you lift it.
  • The prop stability figure assumes a roof panel for a 120 × 150 mm house, using a high estimate of 1.2 g/cm³ for gingerbread density. Larger or heavier roofs need more props. Props are not meant to hold anything but gingerbread.
  • The gable arm assumes the roof line passes through the outer top edge of the side walls, as on a standard gingerbread house template. If your gable sits between the side walls, the clip still fits but leaves a small gap over the gable.
  • Clips must come off before the roof goes on. The roof panels in the picture are short sections placed between the clips so both steps show in one view.
  • Checked in the Loftsmith engine only; the fit on real baked gingerbread has not been tested.

Comments