From the Loftsmith Workshop

Ornament and mineral specimen shipping box, 20-80 mm

Gets a glass ornament or a mineral specimen to a friend without a crack. The item sits inside a round shell with tall slots down the sides, so you can see it's in there. The lid screws on, and a little ridged band at each end gives your fingers something to hold.

5 parts · 119 g · 91 × 91 × 103 mm

by Loftsmith Workshop

Round dark grey screw-top canister with tall slots showing an orange item inside
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • tube · PETG · Upright, either end down (it is symmetric)

    The main body: an internal 3-start thread and a 45-degree clamping ledge at each end, plus nine 8 mm wide windows with chamfered mouths at the defaults. PETG for toughness, and it softens at a higher temperature than PLA in a hot parcel van.

  • plug-bottom · PETG · Roof down on the bed

    Screw-in end plug: a 10 mm head with a fluted grip band and a plain 2 mm roof chamfer. Its hollow spigot gives the arms room to swing. Same geometry as plug-top.

  • plug-top · PETG · Roof down on the bed

    Identical to plug-bottom: print the same file twice.

  • cradle-bottom · TPU 95A · Arms flat on the bed, cup facing up

    Six curved flexure arms between a clamped outer ring and a cup shaped to the item; the arms are the spring. The arm check counts only the printed walls and skins, so the default 2 walls and 15% infill are enough.

  • cradle-top · TPU 95A · Arms flat on the bed, cup facing up

    Identical to cradle-bottom: print the same file twice.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None. Every part prints flat-side down; threads, ledges and window mouths stay within 45 degrees.
Notes
Whole set (tube, two plugs, two TPU cradles) at 2 walls and 15% infill: about 123 g and 3 h 12 min. That is the engine's estimate for the default sliders, and the setting the arm check assumes, since it counts only the arms' 2 perimeters and 4 top and bottom layers. Print the two cradles in TPU 95A,

Hardware

  • Cushioned outer shipping box · Not printed. The capsule goes inside a padded box; it is not a shipping container on its own.

Assembly

  1. Drop cradle-bottom into the bottom end of the tube, cup facing into the tube, so its chamfered ring meets the 45-degree ledge.
  2. Screw plug-bottom into that end clockwise, about three-quarters of a turn (270 degrees), until its rim clamps the TPU ring against the ledge.
  3. Stand the tube on its plug and set the item in the bottom cup, long axis vertical.
  4. Lower cradle-top into the open end, cup facing down onto the item, and screw in plug-top clockwise until it is snug.
  5. Look through the windows to check that the item sits in both cups and touches nothing else.
  6. Pack the capsule upright inside a cushioned outer box. To open, turn the top plug anticlockwise about three-quarters of a turn and lift the top cradle out.

Good to know

  • The travel figure is a calculation, not a drop test: it is an upper bound on how far the arms deflect under the item's weight times the design shock. It does not promise the item survives any particular drop. Always ship the capsule inside a cushioned outer box.
  • The arm sizing uses the engine's TPU 95A modulus (30 MPa) and counts only 2 printed perimeters and 4 top and bottom layers. A softer or stiffer TPU, or thinner walls, will change the real travel.
  • Sideways the arms are much stiffer than up-down (0.93 mm computed travel at the defaults), so side knocks are cushioned far less. Pack it upright and mark the outer box this way up.
  • The cups are shaped for an egg- or ball-shaped item of the width and height you set. Very irregular minerals may need a wrap of tissue to sit snugly, and an item shorter than the height setting will rattle.
  • The windows are open slots: the capsule is not dust- or waterproof, and a thin object could poke through.
  • At the defaults it is about 123 g and 3 h 12 min of printing. With item width at 80 mm and the other sliders at their defaults, the engine reports 111.2 x 111.2 x 103.3 mm and about 166 g and 4 h 7 min at 2 walls and 15% infill.

Comments