From the Loftsmith Workshop
Planetary vernier drive and dial for 1/4 in or 6 mm shafts
A fine-tuning knob for anything you want to set by tiny amounts, with a printed dial so you can read where you are. Turn the orange knob and a ring of planetary gears eases the shaft round slowly. It suits 1/4 in or 6 mm shafts, and you can resize the dial and the shaft length.
7 parts · 68 g · 144 × 120 × 50 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- housing · PLA · Front face down (print group 'drive' with sun and planets, one object)
Fixed ring gear with two arms, panel posts and the tapered index fin at 12 o'clock. Press an M3 heat-set insert into each post end. PLA for stiff, crisp teeth and clean print-in-place gaps.
- sun · PLA · Front face down, printed in place inside the housing
15 teeth, module 1, with a 6 mm hex socket for the knob.
- planet 1 · PLA · Front face down, printed in place
30 teeth, with a 7 mm stub axle that drives the dial.
- planet 2 · PLA · Front face down, printed in place
Same as planet 1, 120 degrees round.
- planet 3 · PLA · Front face down, printed in place
Same as planet 1, 240 degrees round.
- dial · PLA · Scale face down on a smooth or textured plate, hub up
120 mm output disc with the set-screw hub. Drop an M3 nut into the hub slot.
- dial scale · PLA (second colour) · Prints with the dial as one object, first 0.6 mm
Dark 0-100 scale inlaid flush in the dial face on filament 2. Switch the two-colour option off for a one-colour engraved scale.
- knob · PLA · Front face down, hex spigot up
36 mm fluted knob. Push the hex into the sun.
Print settings
- Layer height
- 0.2 mm (0.16 mm gives smoother teeth on the drive group)
- Walls
- 3 walls (recommended, so the posts are solid round the heat-set inserts): about 98 g, 3 h 4 min for everything at 15% infill. 2 walls is the lighter option at about 72 g, 2 h 17 min, with thinner post walls round the inserts
- Infill
- 15%
- Supports
- None. Every part prints without supports.
- Notes
- Print the drive group (housing, sun, planets) on its own and keep it one object so the 0.15 mm gaps survive. Turn on elephant-foot compensation (about 0.15 mm) and no brim on that object. The two-colour scale adds about 3 filament changes (about 1.6 g of purge, included in the figures). Print a clea
Hardware
- 2 × M3 heat-set insert (4.1 mm hole, 5.7 mm long) · One in the panel end of each post
- 2 × M3 x 8 socket screw · From behind the panel into the inserts; use panel thickness + 6 mm (M3 x 8 suits a 2 mm panel). Drill two 4 mm holes level with the shaft, the dial diameter + 13.4 mm apart (133.4 mm for the 120 mm di
- M3 hex nut · Drops into the slot in the dial hub
- M3 x 5 set screw (cup point) · Clamps the shaft; bears on the flat of a D-shaft
- Long-arm 1.5 mm hex key or 1.5 mm hex screwdriver, at least 78 mm reach (a standard short L-key will not reach) · Goes in sideways at 12 o'clock between the panel and the dial to the set screw. The reach needed is the dial radius + about 17 mm: 78 mm for the 120 mm dial, up to 90 mm for the 140 mm dial
Assembly
- Free the printed drive: put the knob's hex into the sun and turn it back and forth a few full turns until the planets roll smoothly.
- Press an M3 heat-set insert into the panel end of each post.
- Drop the M3 nut into the slot in the dial hub and start the M3 x 5 set screw.
- Drill two 4 mm holes in the panel level with the shaft centre, one each side, the dial diameter + 13.4 mm apart (133.4 mm for the 120 mm dial). The extra 0.6 mm lets the drive centre itself on the shaft.
- Turn the capacitor or pot to the end you want to read 0. Slide the dial onto the shaft (scale facing you) until the hub is about 1.5 mm off the panel, turn 0 to 12 o'clock, and tighten the set screw. Use a long-arm 1.5 mm hex key or 1.5 mm hex screwdriver with at least 78 mm reach (dial radius + abo
- Slide the printed drive onto the dial so the three planet stubs drop into the dial's holes, turning the housing until the posts line up with the panel holes.
- Fit two M3 screws from behind the panel into the post inserts, turn the knob a few turns to centre everything, then tighten.
- Push the knob's hex into the sun (a drop of glue if it comes off). The tapered fin at 12 o'clock is the index.
Good to know
- For hand tuning, not precision positioning. At the default gear gap the engine estimates about 2.6 degrees of play at the dial, which is about 16 degrees of dead knob travel when you reverse. The scale is on the output, so the reading stays true. Approach a setting from the same direction.
- The drive multiplies your twist. A firm 0.3 N m on the knob puts about 1.8 N m on the shaft at 6:1, so turn gently at the end stops of a potentiometer.
- Ratios are limited to 4:1, 5:1 and 6:1. 8:1 or 10:1 in one stage would need a sun gear too small to print cleanly.
- The shaft must come straight through the panel and stick out between 8 mm and the slider value + 0.4 mm. Cut longer shafts. A pot's threaded bushing and nut in front of the panel is not accounted for: the dial hub sits 1.5 mm off the panel.
- Tightening the set screw needs a long-arm 1.5 mm hex key or hex screwdriver (at least 78 mm reach for the 120 mm dial); a standard short L-key will not reach the hub.
- Fits, gear gaps and strength are checked in the Loftsmith engine with typical PLA properties; this design has not been printed or tested. Run a clearance test first and adjust the Gear gap slider.
- PLA softens at about 55 C. For a hot enclosure print in PETG and re-check the gear gap.
- With the two-colour option off, the scale is engraved into the bed-side face, so each mark has a small bridged roof and a lower-contrast look.
Comments