From the Loftsmith Workshop
Hanging departure board case for 3.12in SSD1322 OLED
A little desk stand for a 3.12in SSD1322 OLED, so a departure-board display hangs in the air instead of lying flat. The screen sits in a dark case with a glowing window, swinging from a grey arch on a low base. Change the module width and height to match your board.
5 parts · 157 g · 173 × 84 × 122 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- sign-front · PLA · Face down on the bed (printRotate 90,0,0); window chamfer and pockets open upward, no supports
120.4 x 40.5 x 13.9 mm, ~15 g, ~25 min. Holds the glass in its own pocket behind a 79.8 x 22.2 mm window. Press two M2.5 heat-set inserts into the end walls.
- sign-back · PLA · Face down on the bed (printRotate -90,0,0), no supports
120.4 x 40.5 x 21.2 mm, ~19 g, ~31 min. With one display it carries the four clamp fingers that press the PCB edge. With two displays it gets its own window, and the case needs the extra clamp-bar part (2 pieces).
- gantry · PLA · Lying on its back (printRotate -90,0,0); the lead groove opens onto the bed, no supports
165.4 x 107.1 x 10 mm at a 30 mm drop, ~24 g, ~36 min. Portal frame, both drop rods with T-heads, flared feet and tenons in one flat print, so the layers run along the rods.
- base · PLA · Upside down, top face on the bed (printRotate 180,0,0), no supports
173.4 x 84 x 23.6 mm, ~68 g, ~94 min. Leg sockets, front ballast bay, touch-pad cell with a 1.6 mm skin and an engraved ring, USB opening at the back, four M3 heat-set inserts.
- base-cover · PLA · Flat as modelled
173.4 x 84 x 9.4 mm, ~32 g, ~46 min. Bottom plate with four corner ledges that cradle the controller board; four M3 x 8 countersunk screws.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- PLA. At 2 walls and 15% infill the whole set is about 163 g and 4 h 1 min, with every part fitting a 180 mm bed. At 3 walls and 15% it is about 223 g and 5 h 28 min. Print the sign halves face down for a clean bezel and the base upside down so the touch-pad skin and engraved ring print on the bed. D
Hardware
- 3.12 in 256x64 SSD1322 OLED module · Two for the back-to-back option. Set the PCB width and height sliders to your module's outline (89-104 x 32-46 mm).
- ESP32 D1 Mini (about 31.2 x 39 mm) or Raspberry Pi Zero (65 x 30 mm) · Choose on the Controller board option; held on corner ledges with double-sided foam tape
- 7 × Female-female jumper wires, 30 cm · 7 for one display (SPI), 8 for two (second chip select); twist or sleeve them into a bundle of about 4 mm
- 2 × M2.5 heat-set inserts · In the sign-front end walls
- 2 × M2.5 x 12 socket head screws · Length at the defaults; two displays at default settings use M2.5 x 16. The build log states the length for your slider settings.
- 4 × M3 heat-set inserts · Base corner pillars
- 4 × M3 x 8 countersunk screws · Base cover
- 150 × Steel washers or coins · Grams of ballast for the front bay (it holds about 318 g at the default depth)
- 1 mm foam tape · Small pads on the clamp finger tips (or clamp bars) and to fix the board and touch pad
- TTP223 capacitive touch module (about 15 x 11 mm) · Optional; taped under the 1.6 mm skin at the front of the base
- USB lead for the controller · Plugs in through the 13.5 x 9 mm opening at the back of the base
- 4 × Stick-on rubber feet · Optional
Assembly
- Measure your OLED module's PCB width and height, and the height of its header plus the connectors behind it. Set the Display module width, height and Room behind each display sliders to match.
- Press two M2.5 heat-set inserts into the sign-front end walls and four M3 heat-set inserts into the base corner pillars.
- Thread the jumper wires (7 for one display, 8 for two) down through the 8.5 mm hole behind the right leg socket and into the base. Twist or sleeve them into a roughly 4 mm bundle.
- Push the gantry's two tenons into the base sockets. Press the bundle into the snap-in groove down the back of the right leg, along the beam and down the right rod, leaving the ends hanging below the right T-head.
- Lay the OLED module glass-first into sign-front so the glass drops into its pocket behind the window. Rest the T-heads in the top-wall slots, with the rods standing in the half slots.
- Plug the jumpers onto the module header. One display: put 1 mm foam pads on the four clamp fingers of sign-back. Two displays: fit the second module into sign-back, then drop in the two clamp bars with foam on both faces, the notched one at the top with its notches round the rod heads.
- Close sign-back onto sign-front and drive the two M2.5 socket screws from the back. The T-heads are now trapped and the sign hangs from the rods.
- In the base: fix the controller board on the cover's corner ledges with foam tape, USB end to the back. Tape the TTP223 under the thin skin at the front, with its wires through the corridor to the board bay. Fill the front bay with about 150 g of steel washers or coins.
- Connect the display wires and the touch pad to the board, screw the cover on with four M3 x 8 countersunk screws, and plug the USB lead in through the back opening.
Good to know
- Checked in the Loftsmith engine only; nobody has printed or tested this design. Fit, clamping and the snap-in groove need a real print.
- SSD1322 modules vary. The case locates the 88 x 27.8 mm glass and assumes it sits within about 1.2 mm of the PCB centre; it does not use the module's mounting holes. Measure yours before printing.
- The ESP32 D1 Mini outline is taken as 31.2 x 39 mm with the USB socket centred on a short edge. Check your board, since clones differ.
- The SPI wires run about 30 cm from the base to the display. If the screen glitches, lower the SPI clock in your firmware.
- The groove holds the wire bundle in place but is not strain relief, so don't pull the display wires from outside.
- The clamp fingers or bars stop 0.8 mm short of the PCB on purpose. Use the 1 mm foam pads so the glass is never clamped hard.
- With 150 g of ballast the board tips at about a 1.9 N push at the sign centre, and at about 1.45 N without ballast. It is a desk ornament, not for shelves that get knocked.
Comments