From the Loftsmith Workshop
Self-centering tap wrench for DIN 352 taps, M3 to M6
Turns a small hand tap without wobbling it off-line. Three jaws close around the square shank and centre it as you tighten the little knob, and the two flat wings give you something comfortable to push against. Change the tap square range and wing length to suit your taps.
7 parts · 22 g · 100 × 69 × 14 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- body · PLA · Flat on its underside as modeled
Hub and T-bar in one piece, 99.9 x 54.8 x 12.1 mm, graphite. The pocket and nut slot open upward, and the screw hole and thumbwheel bore are teardropped, so it needs no supports. 4 walls.
- cap · PLA · Upside down: top face on the bed, nut tab standing up
A silver ring with a 20 mm window that shows the jaws. The hex pocket in the tab has a pointed roof so it prints without support.
- jaw-1 · PLA · Flat on one end face
Orange. All four jaws are the same shape. Print at 100% infill.
- jaw-2 · PLA · Flat on one end face
Same shape as jaw-1. 100% infill.
- jaw-3 · PLA · Flat on one end face
Same shape as jaw-1. 100% infill.
- jaw-4 · PLA · Flat on one end face
Same shape as jaw-1. 100% infill.
- thumbwheel · PLA · Neck down, wheel end up
A grooved orange knob with an 11 mm neck that slides into a bore in the side of the hub. The screw head presses into the pocket at its outer end.
Print settings
- Layer height
- 0.2 mm
- Walls
- 4 walls for the body and cap; jaws at 100% infill
- Infill
- 20% for the body, cap and thumbwheel; 100% for the four jaws
- Supports
- None
- Notes
- At the recommended 4 walls and 20% infill the build report gives about 35 g and 1 h 42 min for all 7 pieces. Solid jaws add a little more because they are small. At the page's default stats settings (2 walls, 15% infill) the report gives about 22 g and 1 h 6 min. Print the cap in silver or grey and
Hardware
- M4 x 30 socket head cap screw (ISO 4762) · At default settings. The build picks the length and shows it in the screw's name in the 3D view. With the M3 option, use an M3 screw of the length shown.
- M4 hex nut · Sits in the cap's tab. Use an M3 nut with the M3 option.
Assembly
- Press the M4 nut into the hex pocket in the cap's tab.
- Drop the four jaws into the square pocket like a pinwheel, as in the picture. Each jaw's flat back slides against one pocket wall, its long angled face points toward the centre, and its short face rests against the next jaw. A little dry lubricant (PTFE spray or graphite) on the jaw faces helps them
- Lower the cap onto the hub so the tab with the nut drops into the slot beside the pocket. The jaws show through the cap's window.
- Push the M4 x 30 screw through the thumbwheel from its outer end and press the head into its pocket.
- Slide the thumbwheel's neck into the bore on the side of the hub and thread the screw through the nut until it touches the jaw.
- Back the screw off a turn and push the tap's square up through the hole in the underside. Tighten the thumbwheel finger-tight, checking through the window that all four jaws have closed on the square.
- To take it apart, unscrew the thumbwheel fully. The cap then lifts off and the jaws come out.
Good to know
- This is a fingertip tool. At the rated 0.31 N·m on a 4.9 mm square, the push you can apply is about 7.7 N (0.79 kg) with one hand at the middle of a grip, 40 mm from the centre, or 3.9 N per hand with both. Turn it with your fingertips. A longer T-bar (up to 150 mm on the slider) makes overloading e
- Each tap size is rated at its own DIN 352 square and an approximate square length: M3 2.7 mm square, 5 mm long; M4 3.4 mm, 6 mm; M5 and M6 4.9 mm, 7 mm (check your tap). With the default M4 screw, the screw tip pushing on the plastic jaw is the weaker limit for every size, so the shorter M3 and M4 s
- A friction estimate (PLA on PLA, coefficient 0.35) shows the jaw chain does not lock, since locking needs a coefficient of 0.41 or more. But only about 11% of the push passes from one jaw to the next while they slide, so the last jaw is moved gently. A dry, slightly sanded or lubricated set of jaws
- Tighten the thumbwheel finger-tight only. The jaws hold the tap by its square shape, not by squeezing it, and the screw tip on PLA is the weak point.
- Sizes are for DIN 352 taps only. M8 DIN 352 taps have a 6.2 mm square and do not fit (the largest-square slider stops at 5.5 mm). ISO 529 taps use different squares, so set the smallest and largest square sliders (2.0 to 3.4 mm and 4.0 to 5.5 mm) to match yours.
- Clearance is 0.1 mm between jaws and 0.05 mm per side at the tap, so the square can sit up to about 0.05 mm off centre before printing tolerance is counted. A print that comes out oversized may need the jaw faces lightly sanded.
Comments