From the Loftsmith Workshop

Horizontal hole test: round, teardrop, flat-top, diamond

Print this before you commit to a part with sideways holes, and see which hole shape your printer actually handles best. Each size comes in round, teardrop, flat-top and diamond, and the little pins check how a screw or rod fits. Change the smallest hole and the step between sizes to match your parts.

4 parts · 38 g · 99 × 30 × 114 mm

by Loftsmith Workshop

Upright orange plate with rows of round, teardrop and diamond holes in graded sizes and three grey pins
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • hole-test-plate · PLA · Standing upright on its foot, exactly as modelled (99 x 30 x 114 mm). The holes must print horizontal, so do not lay it flat.

    About 37 g and 63 min at 2 walls / 15% infill. Rows of round, teardrop, flat-top and diamond holes at 4, 6, 8, 10 and 12 mm; M3-M8 bolt row on top; settings tag engraved on the foot. PLA because the test needs no heat or flex resistance; print it in the filament you want to test.

  • pin-0.00 · PLA · Head down on the bed, shaft up (so it prints truly round)

    8.00 mm pin with 1 notch: zero clearance in the 8 mm hole.

  • pin-0.10 · PLA · Head down on the bed, shaft up

    7.90 mm pin with 2 notches: 0.1 mm clearance.

  • pin-0.20 · PLA · Head down on the bed, shaft up

    7.80 mm pin with 3 notches: 0.2 mm clearance.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None. The holes are the test, so supports would defeat it.
Notes
At these settings the plate and three pins together come to about 40 g and 1 h 23 min (engine estimate; the plate alone is about 37 g and 63 min, about 6 min per pin). Everything fits a 180 mm bed. Use your normal profile and nozzle for the filament you want to test, so the results match your real p

Hardware

  • 5 × M3, M4, M5, M6 and M8 bolts · Optional, one of each, any length of 8 mm or more, to try in the bolt row. Not needed to print or use the hole rows.

Assembly

  1. Print the plate standing on its foot and the three pins head down, all with no supports.
  2. Without cleaning out the holes, look at the top of each hole: compare how much each row sags at each size.
  3. Push the 1-notch pin (0 mm clearance), then the 2-notch (0.1 mm) and 3-notch (0.2 mm) pins through every hole in the middle (8 mm) column. Each shape is drawn around the same 8 mm circle, so the loosest pin that still goes through shows how much that shape closes up.
  4. Try M3-M8 bolts in the top row to see whether the ISO 273 clearance holes pass a bolt in the shape you chose.
  5. Use the winning shape and the size from which it prints cleanly in your designs; change the teardrop angle, flat-top allowance or bolt-row shape with the sliders and print again to compare. The settings are engraved on the foot.

Good to know

  • The fits, webs, stability and bolt clearances were checked in the Loftsmith engine, not on a real printer. The results depend on your printer, filament, cooling and slicer.
  • Printed holes usually come out a little undersize, and elephant's foot can narrow the bottom rows, so treat the 0 mm pin as a reference rather than a fit you should expect.
  • The pins are sized for the middle column only (8 mm by default); other columns have no matching pins.
  • This tests hole shape only, not threads, press-fit inserts or load capacity. The plate is a gauge and is not meant to carry weight.
  • At the defaults the plate is 99 x 30 x 114 mm and about 40 g, more than a quick calibration coupon. Fewer or smaller hole sizes make it shorter and lighter.

Comments