From the Loftsmith Workshop

Christmas carousel for 18-note music box movements

A little carousel that turns on the shaft of an 18-note music box movement and gives your winding key a reason to be on display. The riders sit on posts under a scalloped canopy, and the ribbed base has an arch for the movement. Change the movement size and the shaft position to fit yours.

13 parts · 128 g · 108 × 108 × 138 mm

by Loftsmith Workshop

Red carousel with a scalloped canopy, white riders on posts and a ribbed round base with an arched opening
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • base · PLA (red) · Deck side down; the arches open upward so nothing bridges

    108 x 108 x 42.5 mm, about 51 g and 75 min. Holds the movement on two end brackets with M2 tap holes.

  • cam-ring · PLA (cream) · Flat side down, wave on top

    About 7 g, 14 min. Fixed wave track the rider pins ride on.

  • button-left · PLA (cream) · Flat contact face down

    Turn button that holds one end of the movement's bedplate.

  • button-right · PLA (cream) · Flat contact face down

    Turn button that holds the other end of the bedplate.

  • column · PLA (cream) · Upright, hub end down

    About 6 g, 18 min. Hub bore pushes onto the shaft; hex drives the platform; twisted fluted pole carries the canopy.

  • platform · PLA (red) · Flat, guide bosses up

    About 22 g, 33 min. Scalloped disc with a 12 mm square guide for each rider.

  • canopy · PLA (red) · Upright on its flat underside

    About 33 g, 51 min. Scalloped, ribbed roof with a finial; it also keeps the riders captive.

  • rider-1-tree · PLA (cream) · Flat on its back face

    About 1 g. Cut-out tree on a 4 mm square pin.

  • rider-2-gift · PLA (cream) · Flat on its back face

    About 2 g. Gift box with a bow.

  • rider-3-star · PLA (cream) · Flat on its back face

    About 1 g. Five-point star.

  • rider-4-bauble · PLA (cream) · Flat on its back face

    About 2 g. Bauble with cap and hanging loop.

  • rider-5-tree · PLA (cream) · Flat on its back face

    About 1 g.

  • rider-6-gift · PLA (cream) · Flat on its back face

    About 2 g. The Number of riders slider changes how many rider parts there are (3 to 6; the shapes repeat tree, gift, star, bauble).

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None. Every part prints without supports in the orientation given.
Notes
Whole set at the defaults: about 132 g and 4 h 7 min at 2 walls / 15% infill (the engine's estimate). For a sturdier base use 3 walls / 15%: about 176 g and 5 h 27 min for the set. Two colours: red for the base, platform and canopy; cream for the cam ring, column, turn buttons and riders. PLA is fin

Hardware

  • 18-note wind-up music box movement with a rotating output shaft · Not included. Measure its length, width, height (without shaft), shaft diameter, shaft height and shaft offset, and set the sliders. Defaults: 51 x 44 x 19 mm, 3 mm shaft standing 14 mm above the move
  • 2 × M2 x 8 mm screw (self-tapping for plastic, or a machine screw cut into the printed 1.7 mm hole) · Holds the two turn buttons under the end brackets.
  • 3 × 1.75 mm filament offcut, about 7 mm long · Locating pins between the deck and the cam ring.
  • Tape or a drop of glue (optional) · Only if the hub is loose on your shaft.

Assembly

  1. Press three 7 mm pieces of 1.75 mm filament into the holes under the cam ring, then set the ring on the deck so the pins drop into the deck holes. A drop of glue stops it lifting.
  2. Turn the base upside down. Slide the movement in from below between the two end brackets, shaft first through the deck hole, key pointing out of the open bottom.
  3. Screw a turn button under each end bracket with an M2 x 8 screw, lip turned inward under the bedplate. Keep them snug but not tight so they can be swung 90 degrees later to release the movement.
  4. Stand the base up. Push the column's hub straight down onto the shaft until it rests on the shaft tip. Wrap the shaft with tape or add a drop of glue if the hub is loose.
  5. Lower the platform over the column until its hex hole seats on the hub shoulder.
  6. Drop each rider's square pin into a guide boss, rounded face outward. The pin tips rest on the cam.
  7. Press the canopy's socket onto the peg at the top of the column. It now stops the riders lifting out.
  8. Wind the key through one of the arches and let it play. The platform turns with the shaft and the riders rise and fall twice per turn.

Good to know

  • It needs a movement with a rotating output shaft. A plain flat movement without one cannot turn it.
  • The turning parts weigh about 70 g at the defaults (platform, canopy, column and riders). Whether your movement has the torque for that, plus the cam friction, was not checked. Test it before you glue anything.
  • The base leaves 16 mm under the bedplate for the winding key and stem. A longer key will touch the table.
  • The hub bore gives 0.1 mm of play per side on a round shaft, which depends on your printer. Threaded or knurled shafts may need the bore opened up, or tape or glue.
  • The rider no-jam check is a textbook estimate that assumes PLA-on-PLA friction of 0.35. It has not been confirmed on a real print.
  • Small parts: this is a decoration, not a toy for young children.

Comments