From the Loftsmith Workshop
Impulse sealer table set to your bar height, fold-flat legs
A little table that holds your bag steady while you seal it. It sits in front of the sealer at bar height, with slots along the top and legs that fold flat for the drawer. Set the bar height and table width to match your machine.
4 parts · 98 g · 169 × 123 × 67 mm
Loading the 3D view
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- table top · PETG · Top face down on the bed; prints as one object together with both legs (print group 'table').
160 x 120 x 8 mm at defaults, about 68 g. Hex-ribbed underside, five guide grooves on the face. PETG for heat margin next to the sealer.
- leg right · PETG · Prints standing up on its hinge knuckles, in place on the table top (same print group).
About 13 g. Folds first; sits 0.4 mm outside its hinge.
- leg left · PETG · Prints standing up on its hinge knuckles, in place on the table top (same print group).
About 14 g. Sits one leg-thickness further out so it folds flat under the right leg.
- guide fence · PETG · Lying on its flat back face, tongue edge on the bed.
About 3 g, 108.8 mm long at defaults. Press-fits (0.1 mm) into any groove; the tongue has a 0.5 mm lead-in.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 (use 3 for a stiffer top: about 140 g, 3 h 40 min)
- Infill
- 15 %
- Supports
- None
- Notes
- Default sliders at 2 walls / 15 % infill: about 102 g and 2 h 39 min in total (table top 91 min, each leg about 27 min, fence 8 min). The table, both legs and the hinge pins export as one object with the 0.4 mm hinge gaps kept: do not merge or re-orient them, and keep any brim off the hinge area. Th
Assembly
- Measure from the counter to the top of your sealer's sealing pad and set Bar height; measure from the sealer's front edge to the middle of the heating strip and set Sealer front edge to bar centre.
- Print the table group face down in one go with no supports. Print the fence on its flat back.
- Let the print cool, then work each leg gently back and forth a few times until the hinge swings freely. If a hinge stays fused, reprint with the Hinge gap slider at 0.45 or 0.5 mm.
- Press the fence tongue into the groove you want: the first groove is the Seal line to fence value, and each groove forward adds 10 mm.
- Stand the table with its back edge against the sealer's front edge. The legs lean out onto their stops and the top sits level with the bar.
- Lay a bag on the table with its open end over the sealing bar and push the filled part up to the fence, then seal.
- To store it, lift the table, fold the right leg under first, then the left leg under it.
Good to know
- Bags only: the table is not a food-contact surface.
- The fit to your sealer depends on two measurements you enter (bar height and the distance from the sealer's front edge to the bar centre). The model assumes a sealing pad about 8 mm wide and the table pushed against the sealer's front edge.
- There is no catch for storage: folded legs swing open if you lift the table right side up. Store it top-down, flat in a drawer, or with a rubber band around it.
- Widths stop at 230 mm (one piece on a 256 mm bed). On a 300 or 400 mm sealer it supports the middle of the bar, not the full length.
- The 0.4 mm hinge gap and the 0.1 mm fence press fit are not physically tested. Print the table and check the hinges free up, then tune the Hinge gap slider. Glue the fence or sand its tongue if the fit is loose or tight.
- Loads were checked for a 500 g bag set down hard plus a 20 N hand press on one end. It is not meant for leaning on or for loads over about 2 kg.
- Keep the sealer's hot bar and arm off the plastic. The table is designed to stay at least 6.5 mm from the sealing pad.
Comments