From the Loftsmith Workshop

Camera bump pad and drawing wedge for phones and tablets

Props your phone or tablet at a drawing angle and gives the camera bump somewhere to sit, so the screen stops rocking when you press. A raised lip along the low edge stops it sliding off. Set the camera bump's position and your device's width to match your own.

5 parts · 53 g · 67 × 164 × 31 mm

by Loftsmith Workshop

Teal sloped wedge with four long slots in the top and a curved lip along the low edge
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • pad · PLA · Flat bottom down, as modelled; no supports

    67 x 164 x 30 mm at the defaults (10° wedge), about 53 g and 75 min on its own. PLA because it has to stay stiff under the device. It has a chamfered camera-bump pocket in a solid land with no windows, stadium windows elsewhere, and a front stop with a stylus groove.

  • foot ×4 · TPU · Rounded top down (printRotate 180), chamfered contact face up

    Discs 6 mm across and 1.6 mm tall in TPU 95A for grip and a little give. Each sits 0.8 mm deep in a corner socket and stands 0.8 mm proud. Under 1 g each.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
At the defaults (example phone, 10° wedge) the whole print is about 54 g and 1 h 34 min at 2 walls / 15% infill (3 walls / 15%: about 68 g, 1 h 53 min). Print the four feet separately in TPU 95A, slowly; they take a few minutes each. Steeper angles and larger devices use more filament, so check the

Hardware

  • CA (super) glue · One small dot per foot socket

Assembly

  1. Measure your device: width, length and thickness (with its case if you use one). Then measure the camera bump: width, length, height, and its centre from the left and top edges, with the screen facing up. Set the sliders to match; the defaults are only an example phone.
  2. Choose the wedge angle: 0° for a flat leveller, about 10-15° for drawing.
  3. Leave Pocket clearance at 1.0 mm unless you are sure of your measurements.
  4. Print the pad flat in PLA and the four feet in TPU.
  5. Turn the pad over and glue a TPU foot into each of the four shallow corner sockets.
  6. Set the pad on the desk with the stylus groove toward you. Lay the device on it screen up, bottom edge against the front stop, so the bump drops into the chamfered pocket.
  7. If you draw with a stylus, rest it in the groove at the front.

Good to know

  • The default sizes (72 x 148 x 8 mm, with a 36 x 36 x 2.5 mm camera bump 50 mm from the left and 22 mm from the top) are a generic example, not a particular phone. Measure your own device and bump before printing.
  • If the bump position or size you enter would put it past the device edge, the pad limits it to stay 2 mm inside the outline. The check detail on the page says when this happens.
  • The pocket allows 1.0 mm per side by default, so small measuring errors are fine. If you lower Pocket clearance toward 0.3 mm, measure carefully: if the bump touches the pocket, the device can rock again.
  • The tipping check assumes a 150 g device and a 5 N press square to the screen at a far corner. On narrow phones the margin is small: the load centre stays about 2.4 mm inside the feet at the defaults and about 1.5 mm at 64 mm wide. Avoid leaning hard on the top corners.
  • The front stop is always on. It holds the device on the slope without relying on friction.
  • These are geometry and statics checks in the Loftsmith engine. The design has not been printed or tested on a real device.

Comments