From the Loftsmith Workshop
ESP32 mini arcade cabinet for 2.4-3.5 in SPI screens
A tiny arcade cabinet for your ESP32 and a little SPI screen, with a marquee up top and a control deck below. The side panels are red, and there are round holes in the deck for buttons. Change the screen measurements and button count to match your parts.
17 parts · 171 g · 105 × 103 × 164 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- side-left · PLA (red) · Outer face down, groove up
164 x 103 x 5 mm, ~28 g, ~40 min. The groove ring keys every front panel.
- side-right · PLA (red) · Outer face down, groove up
Mirror of side-left, ~28 g, ~40 min. Comes off with 3 screws for service.
- kick-panel · PLA (charcoal) · Outer face down
~7 g, ~14 min.
- control-deck · PLA (charcoal) · Outer face down, bosses up
Button holes, a 7.1 mm stick hole and two stick-clip bosses. ~11 g, ~19 min.
- screen-bezel · PLA (black) · Outer face down, bosses up
Bevelled window over the active area plus four bosses that locate the PCB. ~14 g, ~23 min.
- marquee · Translucent PLA (yellow) · Outer face down
Glows if you put an LED behind it. ~8 g, ~14 min.
- top-panel · PLA (charcoal) · Outer face down, lugs up
Two M3 insert lugs. ~9 g, ~17 min.
- back-panel · PLA (charcoal) · Outer face down, lugs up
Speaker grille, speaker-clip bosses, USB opening, two M3 insert lugs. ~35 g, ~51 min.
- base · PLA (charcoal) · Outer face down, pad and tray up
ESP32 pad with locating posts, ballast tray, two M3 insert lugs. ~30 g, ~44 min.
- screen-clip ×4 · PLA · Flat
Slotted clip, 14.5 x 7 x 2 mm, about 4 min each.
- stick-clip ×2 · PLA · Flat
Same slotted clip, holds the 5-way switch board.
- speaker-clip ×2 · PLA · Flat
Same slotted clip, holds the speaker by its end ears.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2 (the page figure: about 177 g and 5 h 8 min for all parts). 3 walls make the screw bosses and lugs tougher: about 242 g, 6 h 49 min.
- Infill
- 15%
- Supports
- None. Every panel prints outer face down; the side panels print with the groove up.
- Notes
- PLA because this is an indoor desk toy: it is stiff, keeps the flat panels square in the grooves, prints cleanly flat, and comes in translucent colours for the marquee. The ESP32 and screen stay well below the 55 °C where PLA softens. Fits a 180 mm bed at the default sizes (largest part: the 164 x 1
Hardware
- 6 × M3 heat-set insert (5.7 mm long) · Into the lugs on the base, back and top panels.
- 6 × M3 x 10 countersunk screw · Three per side panel.
- 8 × M2.5 x 8 pan-head screw · Clips; they cut their own thread in the 2.2 mm printed boss holes.
- Ballast, about 100 g of steel · Steel nuts or washers, or stick-on wheel-balance weights, glued or taped into the base tray (holds about 112 g).
- Double-sided foam tape · Holds the ESP32 devkit on its pad.
- ESP32 devkit (55 x 28 mm) · Not printed. USB end toward the back panel.
- 2.8 in ILI9341 SPI screen module (or the size you choose) · Not printed.
- 5-way switch module, board up to 22 mm along the deck · Not printed; fit your own ball-top cap.
- 2 × 16 mm momentary push buttons · Not printed; the hole slider sets the size.
- 70 x 30 mm speaker with flat end ears · Not printed; the speaker sliders set the size.
Assembly
- Press the six M3 heat-set inserts into the lugs at the ends of the base, back and top panels.
- Push the buttons through the control deck and tighten their nuts. Set the 5-way switch module under the deck with its stem through the 7.1 mm hole, slide the two stick clips over the board edges and screw them down with M2.5 x 8 screws.
- Lay the screen face down on the bezel between the four bosses. Slide it along the bezel until the picture sits in the window, then fit the four screen clips.
- Place the speaker against the back panel grille between its two end bosses and fit the two speaker clips over its ears.
- Stick the ESP32 devkit on the base pad with foam tape, USB end toward the back, between the six locating posts. Fill the ballast tray with about 100 g of steel and glue or tape it down.
- Wire buttons, switch, screen and speaker to the ESP32. Solder to the screen header pins; there is no room for Dupont plugs behind it.
- Lay the left side panel groove up and stand the base, kick panel, deck, bezel, marquee, top and back panels in its groove.
- Lower the right side panel onto the panel ends and drive three M3 x 10 countersunk screws through each side into the inserts.
- Fit your cap on the switch stem and plug the USB lead in through the opening in the back panel. To service, remove the right side's three screws.
Good to know
- The flat panels and square edges are deliberate: each panel stands in the side panels' groove ring, which needs straight edges to key, so only the outside corners are chamfered.
- The screen presets are typical red SPI module outlines (2.4, 2.8 and 3.2 in ILI9341, 3.5 in ILI9488). Measure your board and use the Measured option if it differs. Along its length the screen is aligned by eye before you tighten the clips.
- The 5-way switch is an estimate: a 3.5 mm stem tilting 15 degrees, a 5.5 mm switch body and a board no longer than 22 mm along the deck. Check yours against the 7.1 mm hole.
- Button flanges (hole + 8 mm) and body depths (hole + 6 mm) are estimates. Buttons with long microswitches may need more depth.
- Empty, the cabinet only just resists a firm 2 N sideways push on the stick (1.00x). Fill the base tray with about 100 g of steel.
- The speaker clips press on flat end ears about 4 mm thick (estimate). Thinner frames need a foam shim.
- The ESP32 sits on a 10 mm pad. Header pins pointing down fit, but Dupont plugs underneath do not, so solder the wires.
- Larger screens and more or bigger buttons make the side panels taller; check the part size before printing on a 180 mm bed.
- PLA softens around 55 °C, so keep it out of hot cars and direct sun. Fits, clips and stability are checked in the engine only; this design has not been printed yet.
Comments