From the Loftsmith Workshop
Flip-through game case rack for Switch, PS5 and Blu-ray
Keeps a row of game cases standing up and easy to flip through, instead of stacked in a pile. Each case sits in its own slot, and the front cradle tips so you can see the next spine. Change the case size and count to match your shelf.
9 parts · 141 g · 122 × 169 × 26 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- base · PLA · As modeled, flat on the bed
Two scalloped rails with a boss round every trunnion, a raised full-width front stop and a rear end wall. About 28 g, 42 min. Printed together with all cradles as one object.
- cradle-1 · PLA · As modeled, upright in place in the base
Front cradle; it tips onto the front stop at the flip angle (30° at the default). About 14 g, 25 min.
- cradle-2 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-3 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-4 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-5 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-6 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-7 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place.
- cradle-8 · PLA · As modeled, upright in place in the base
Identical cradle, printed in place. The Number of cases slider adds or removes cradles (4-10).
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- Print the base and all 8 cradles together as one object; the 3MF keeps the gaps. At 2 walls / 15% that is about 146 g and 4 h 10 min of PLA (engine estimate at the defaults). Do not add a brim: it would bridge the 0.6 mm gaps between cradles and the 0.5 mm gaps to the rails. Keep elephant-foot compe
Assembly
- Measure one of your cases and set Case thickness, Case width and Case height (Switch about 105 x 170 x 11 mm; PS5 and Blu-ray about 135 x 170-172 x 13-15 mm). Set Number of cases.
- Print everything as one object, as modeled, with no supports and no brim.
- Free the cradles: hold the rails and rock each cradle forward and back a few times until it swings easily on its trunnions. If one sticks at the bed, run a thin blade along the gap at its foot.
- Stand the rack with the raised front stop toward you and drop each case into its slot from above, cover facing the front. The slots lean the cases back 5° so they rest upright.
- To browse, push the top of the front case forward and it tips onto the front stop. Each cradle you tip after it rests the top front edge of its cradle on the back of the cradle in front, at about 21-22°. The cover behind the last tipped case is then in view.
- To take a case out, tip it forward too so its back is free, pinch it and lift it out along its slot. Tip the stack back upright when you are done.
Good to know
- Checked in the Loftsmith engine, not printed. The print-in-place gaps (0.45 mm round each trunnion, 0.5 mm at the sides, 0.6 mm between cradles) need a printer that holds them. If unsure, print the 4-case version first.
- Only a cradle with a case in it stays tipped. An empty cradle swings back upright, because its centre of mass is 5.2 mm behind the pivot. That is harmless, but it will not hold an open gap on its own.
- The stability checks use an estimated Switch case weight of about 57 g. The tipping and stay-forward results do not depend on case weight as long as all the cases weigh about the same. Sizes vary by region, so measure your cases and use the clearance slider (0.3-1.0 mm per side) if the fit is tight
- One rack holds 4 to 10 cases. For a longer row, print a second rack; the racks do not key together.
- PS5 and Blu-ray widths make the rack wider and deeper than the default; check the size in the editor before printing.
- The rack is not fixed to the shelf. Tipped cases overhang the front by roughly half their height, so leave clear space in front of it.
Comments