From the Loftsmith Workshop
No-glue interlocking tile coaster for 60-95 mm mugs
A coaster for the mug that always leaves a ring on your desk. The tiles lock together inside a rounded frame, so there's no glue and nothing to paint. Set it to the base of your mug or glass and pick how many blocks run along each side.
18 parts · 51 g · 104 × 104 × 9 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- bone block ×8 · PETG (pearl) · Top face up as modelled, 23.4 x 21.3 x 8 mm
Waisted front to back. Front to back, the rows alternate between bone and barrel blocks, starting with bone at the front. Side to side, every block has one concave face and one convex face; the convex face points toward frame-right. About 2 g and 7 min each.
- barrel block ×8 · PETG (slate) · Top face up as modelled, 23.4 x 25.5 x 8 mm
Bulged front to back; fills the rows between the bone rows. Same left/right rule: the convex face points toward frame-right. About 2 g and 8 min each.
- frame-left · PETG (slate) · Flat as modelled, 68 x 104 x 9.2 mm
Left wall plus the left halves of the front and back walls. Its snap finger is on the front wall. About 8 g, 16 min.
- frame-right · PETG (slate) · Flat as modelled, 68 x 104 x 9.2 mm
Right wall plus the right halves of the front and back walls. Its snap finger is on the back wall. About 8 g, 15 min.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None. Every seam face leans at most 35 deg at the default settings (44.5 deg at the steepest slider setting).
- Notes
- PETG because a hot mug base can pass PLA's 55-57 C softening point; PETG holds to about 70 C and takes the frame snap (1.8% strain) better. At 2 walls and 15% infill the whole set is about 53 g and 2 h 36 min. For a stiffer frame, 3 walls and 15% infill comes to about 71 g and 3 h 29 min. The blocks
Assembly
- Lay frame-left flat on the table, its open side to the right.
- Build the front row first. Slide bone blocks in from the right, each with its bulging side (convex at mid-height) facing right, and push them against the left wall's wave.
- Fill the next row with barrel blocks the same way, sliding them along the row in front. Keep alternating bone and barrel rows to the back.
- Push frame-right onto the open side from the right until both snap fingers (front and back seams) click into their notches.
- To take it apart, press each snap finger outward at its tip with a fingernail, slide frame-right off to the right, and slide the rows out the same way.
Good to know
- Hot drinks: PETG holds up to about 70 C, which is fine for a mug of coffee or tea. It is not a trivet for pans, pots or kettles. If you print it in PLA, use it for cold drinks only.
- Liquid seeps through the hairline seams between tiles, so wipe spills promptly. This is a coaster, not a drip tray.
- The tile fit depends on your printer. If blocks bind, raise the Gap slider. If they rattle, lower it. Each tile has about 0.2 mm of up/down play at the default 0.15 mm gap.
- The locking has been checked as geometry in the Loftsmith engine, not by printing. Tilting or twisting a single tile was not modelled, and neither was a hard drop.
- The frame snap is made to open occasionally. Prying it open often will wear the barbs.
- Keep the wave deep enough for the grid. At high grid counts combined with a wide gap and a shallow wave, the lock check can fail, and the Check tab will show that.
Comments