From the Loftsmith Workshop

4-hole ocarina, parametric key G4 to G5, with windway tests

A small ocarina you can print and play the same afternoon, with four finger holes and a range from G4 up to G5. Three little test pieces come along so you can find the windway that sounds best before you commit. Change the body size for a louder voice.

4 parts · 39 g · 132 × 58 × 79 mm

by Loftsmith Workshop

Teardrop-shaped ocarina with four holes, beside three small cream-coloured windway test pieces
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • ocarina · PLA · Upright on its flat base, mouthpiece pointing up (as modelled). No supports.

    Sizes from the 'Every key G4-G5' and 'wall 4 and voice 8' checks. C5 default: 76.9 x 79.1 x 30.0 mm, largest hole 9.2 mm, 33.4 cm³ solid. G5: 60.1 x 63.1 x 24.8 mm. G4: 91.9 x 93.5 x 34.7 mm. C5 at wall 4: 78.6 mm wide, largest hole 9.7 mm. C5 at voice 8: 80.9 mm wide, largest hole 10.5 mm. PLA beca

  • windway-test-0.8 · PLA · Upright on its flat base, as modelled.

    Mini whistle with the same window and labium as the ocarina and a 0.8 mm windway; 1 dimple under the base. 33.0 x 16.3 x 37.1 mm.

  • windway-test-1.1 · PLA · Upright on its flat base, as modelled.

    Same as above with a 1.1 mm windway; 2 dimples under the base.

  • windway-test-1.4 · PLA · Upright on its flat base, as modelled.

    Same as above with a 1.4 mm windway; 3 dimples under the base.

Print settings

Layer height
0.12-0.16 mm (fine layers give a smoother windway and labium edge)
Walls
4 walls. Walls are laid from both the outer and the chamber surface, so 8 loops of 0.45 mm (3.6 mm) fill the 3.2 mm shell solid and it is airtight.
Infill
25% (only the thicker neck and base regions get infill; the shell itself is solid walls)
Supports
None. The chamber roof is a 45 degree point, and every bridge (window top, throat ceiling) is under 10 mm.
Notes
Engine estimate at 4 walls / 25%: about 66 g and 2 h 25 min for the ocarina plus three test whistles. For reference, the page's 2 walls / 15% figures (41 g, 1 h 29 min) are for a print that would not be airtight; don't use that setting. At wall 4 the 4 walls no longer fill the shell completely, but

Hardware

  • Cord or lanyard, about 2 mm thick · Optional. About 70 cm, threaded sideways through the 3 mm hole at the root of the mouthpiece.

Assembly

  1. Print the three windway test whistles first (1, 2 and 3 dimples under the base = 0.8, 1.1 and 1.4 mm windways).
  2. Blow each one softly. Keep the windway height that gives the clearest, steadiest note, and set the Windway height slider to it.
  3. Choose your key on the Key slider and check the predicted pitches and size in the Check tab. Then print the ocarina upright with 4 walls.
  4. If strings cross the window, clear them with a sharp knife. Do not touch the thin labium edge at the bottom of the window.
  5. Thread a cord through the sideways hole at the root of the mouthpiece if you want to hang it.
  6. To play, cover all four holes and blow gently. Fingering (open holes): root = all closed; 2nd = smallest; 3rd = small; 4th = smallest + small; 5th = smallest + large; 6th = smallest + small + large; 7th = smallest + large + largest; octave = all open. In C5 that gives C D E F G A B C.

Good to know

  • The pitches are computed from a Helmholtz model with an estimated window term. Nothing here has been printed or played. Real pitch depends on your breath (blowing hard can push a note 1-2 semitones sharp) and on how your printer forms the window edge, so the whole scale may sit a little off the targ
  • It is a hand-sized ocarina rather than a small pendant: 76.9 x 79.1 x 30.0 mm in C5 and 91.9 x 93.5 x 34.7 mm in G4. G5 is the smallest at 60.1 x 63.1 x 24.8 mm.
  • It only works if the shell is airtight. Use at least 4 walls (5 if you set the wall to 4 mm). A leaky print sounds breathy or won't sound at all.
  • Printed holes often come out 0.1-0.2 mm small, which makes those notes slightly flat. You can enlarge a flat hole carefully with a drill bit, but a hole made too big can't be undone.
  • The fingering chart is computed for these hole sizes (two holes per hand). It may differ from the charts for other 4-hole ocarinas.
  • The largest hole is 9.2 mm at the defaults, 9.7 mm at wall 4 and 10.5 mm at voice width 8.
  • PLA and PETG are not certified food-safe. Mouth contact is your choice, so clean it and don't share it.

Comments