From the Loftsmith Workshop
Snow shovel side handle, D grip clamp for 24-40 mm shafts
Gives a long-handled snow shovel a second grip, so you can steer and lift with two hands instead of bending over the shaft. A D-shaped loop sits on a short arm and clamps round the pole in two parts. Set it to your shaft's thickness.
2 parts · 101 g · 140 × 34 × 165 mm
Loading the 3D view
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- handle · PETG · Lying on its side, flat face down (140 x 140 mm footprint at the defaults, 34 mm tall), no supports
Clamp top half, arm and D grip in one piece. Four side slots take a washer and an M5 nut each. About 91 g / 2 h 3 min of the default total.
- clamp cap · PETG · Lying on its side, flat face down, no supports
Lower half of the clamp with counterbored seats for the bolt heads and washers. About 9 g / 19 min.
Print settings
- Layer height
- 0.2 mm
- Walls
- 4 walls recommended (the page stats use 2)
- Infill
- 20% recommended (the page stats use 15%)
- Supports
- None. Both parts lie flat on their side; the bolt holes are teardrop-shaped so they print without support.
- Notes
- PETG. ASA also works; avoid PLA because it gets brittle in the cold. Default sliders: about 103 g and 2 h 26 min at 2 walls/15% infill (the page figure), or about 163 g and 3 h 51 min at the recommended 4 walls/20% infill. At the defaults the handle fits a 180 mm bed. With the largest sliders it gro
Hardware
- 4 × M5 x 25 socket head cap screw · Bolt length is computed by the script; it stays M5 x 25 across the whole slider range.
- 4 × M5 hex nut (8 mm across flats) · Slides into the hex slots in the handle's ears; the slots stop it turning.
- 8 × M5 flat washer, 10 mm OD, 1 mm thick · One under each bolt head and one under each nut. They spread the clamp load so the plastic is not crushed.
- 4 mm hex key · Tightens the bolts from below.
Assembly
- Measure your shaft with calipers where the handle will sit, about a third of the way down from the top grip. Set Shaft diameter to that number before you export.
- In each of the four side slots on the handle's ears, push a washer into the lower, wider slot and a nut into the hex slot above it, until they stop against the end of the slot.
- Set the handle on top of the shaft and the cap underneath it, with the orange grip standing up from the shaft.
- From below, push each M5 x 25 bolt through a washer and the cap and thread it into its nut.
- Turn the handle round the shaft to the angle that suits your lead hand, then tighten the four bolts a little at a time in a cross pattern. Stop when they are snug: the checks assume about 820 N per bolt, roughly 0.8 N·m, which is firm with a short hex key. Leave a visible gap between the halves; do
- Check the bolts again after the first session, because PETG settles a little under load.
Good to know
- Strength is checked in the engine with estimated printed-PETG values (15 MPa allowed along the layers), a 1.5x jerk factor and a fillet stress factor. It has not been printed or load-tested. The checked maximum design pull is 400 N (about 40 kg of force) at the top of the slider; do not hang more on
- Clamp grip assumes a friction of 0.3 between the plastic and the shaft. On smooth painted metal, or with ice on the shaft, it may slip sooner. You can add a strip of rubber such as an old bike inner tube; if you do, set Shaft diameter to your shaft plus twice the rubber's thickness.
- The bore fits a round shaft. Oval or D-section shafts, which some fibreglass shovels have, will not clamp evenly. The halves can take up a shaft about 2 mm smaller or 2.4 mm larger than the size you set.
- The grip bar runs across the shaft, like the D grip at the top of a shovel. To change its angle, turn the clamp around the shaft before you tighten it.
- Do not overtighten. The washers and the floor under each nut are sized for about 820 N per bolt, and more than that can crush or creep the plastic.
Comments