From the Loftsmith Workshop

Electric toothbrush charger stand with slide-out drip tray

Gives your electric toothbrush charger a proper home, and the spare brush heads a place to drain. Four little pegs hold the heads upright over a teal tray that slides out for emptying. Change the charger size and the pocket fits yours.

4 parts · 88 g · 236 × 87 × 38 mm

by Loftsmith Workshop

White charger stand with four upright brush-head pegs over a teal slide-out drip tray and a loop at one end
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • fit ring · PETG · Flat as modelled

    CAD estimate about 3 g, 9 min. Print it first and drop it over your charger. If the fit is tight or loose, adjust Pocket clearance (0.2-0.8 mm per side) or the charger size sliders before printing the stand.

  • stand · PETG · Upright as modelled, flat base on the bed

    CAD estimate about 56 g, 77 min at the defaults (154 x 80 x 21.7 mm). It needs no supports because the tray bay and grate seat are open at the top.

  • drip tray · PETG · Open side up

    CAD estimate about 15 g, 24 min. The rolled rim and pull tab need no supports.

  • peg grate · PETG · Flat, pegs pointing up

    CAD estimate about 13 g, 23 min. Each peg has six 3 mm drain holes around it.

Print settings

Layer height
0.2 mm
Walls
2
Infill
15%
Supports
None
Notes
PETG, because the stand sits beside a wet basin and PETG softens at a higher temperature than PLA. At 2 walls and 15% infill all four parts together come to about 90 g and 2 h 17 min. The per-part figures in the parts list are the CAD estimate, which adds up to 87.5 g and 2 h 13 min; the 90 g / 2 h

Assembly

  1. Measure your charger's base width, depth and height, then set Charger shape and the three size sliders. The default 65 x 53 x 33 mm oval is a default value, not a measurement of a specific model.
  2. Print the fit ring and drop it over the charger. It should slip on with a small even gap. If it doesn't, change Pocket clearance and reprint the ring.
  3. Measure the opening inside the bottom of a brush head and set Peg diameter a little under it, so the head slides on without forcing.
  4. Print the stand, tray and grate.
  5. Lower the charger into the pocket and lay its lead in the open slot at the back of the pocket, so it leaves the stand low at the back. The mains plug never has to pass through the stand.
  6. Slide the tray in from the front over the two rails until it stops at the back wall.
  7. Drop the grate into its seat above the tray. The seat is wider at the back than at the front, so the grate lifts out but cannot slide forward.
  8. Push the brush heads onto the pegs. To empty the tray, pull it out by the tab at its foot; the grate and heads stay in place.

Good to know

  • The default charger size is a starting value, not a measured model. Measure your own charger and print the fit ring before printing the stand.
  • Peg diameter (6-10 mm) is an estimate of the opening inside a brush head. Measure a head before printing.
  • The grate rests in its seat without a clip, so a head pulled off at a steep angle can lift it. Pull heads straight up.
  • The tray holds 36 ml at the default 14 mm depth and 23 ml at the 10 mm minimum. It does not drain itself, so empty it regularly.
  • The pocket holds the charger only; it is not a waterproof enclosure. Keep the stand out of standing water.
  • The stand resists a tilt of at least 20 degrees at the defaults. This assumes a 150 g brush with its centre of mass 110 mm above the charger, and does not count the charger's own weight.
  • Peg strength, tray fit, drain positions and lead routing were checked in the engine, not on a real print. Test the tray slide and the peg fit on your printer.

Comments