From the Loftsmith Workshop

Bench power supply case for XY6020L / DPS5005, USB-C in

Turns a bare XY6020L or DPS5005 module into a proper bench power supply you can leave on the desk. The face is tilted back so the screen is easy to read, with a window for the display and two round holes for the binding posts. Vent slots run across the roof.

3 parts · 117 g · 252 × 139 × 68 mm

by Loftsmith Workshop

Orange sloped enclosure with a display window, two round holes and roof slots, beside a flat open frame
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • cover · PETG · Front panel face down on the bed (the part tilts back by the tilt angle); no supports

    Sloped front panel with the display cut-out and two post holes, roof vent slots, side walls. 133.3 x 95.9 x 89.0 mm as printed, ~58 g, ~86 min. Corners are rounded 6 mm and roof edges 2.6 mm; where an edge meets the panel face it becomes a 48° bevel so it prints without support. Press 4 M3 heat-set

  • base · PETG · Floor down on the bed; no supports

    Floor plus back wall with the input opening and rails for a USB-C trigger board. 133.4 x 94.4 x 68.0 mm, ~48 g, ~71 min.

  • fit-frame · PETG · Flat on the bed

    Print first. Same 2.4 mm thickness as the front panel, with three cut-outs at the chosen clearance +0, +0.2 and +0.4 mm (marked 1, 2, 3 dots). ~12 g, ~19 min.

Print settings

Layer height
0.2 mm
Walls
2 walls
Infill
15%
Supports
None
Notes
PETG. At 2 walls and 15% infill: the case (cover + base) is about 106 g and 2 h 37 min; all three parts including the fit frame are about 122 g and 3 h 3 min. At 3 walls all three are about 160 g and 4 h 0 min. Every part fits a 180 mm bed. Print the fit frame first.

Hardware

  • 4 × M3 heat-set insert (about 4.1 mm hole, 5.7 mm long) · In the cover: 2 in the rear corner blocks, 2 in the front bosses. 4 more only if you switch on the converter-board bay (one per standoff).
  • 4 × M3 x 8 countersunk screw · 2 through the back wall, 2 up through the floor
  • 2 × 4 mm banana binding post, red and black · Hole slider defaults to 9.5 mm (3/8 in); set it to your posts. Checked: caps up to 19.1 mm across fit on the 19.05 mm spacing, and 28 mm tails behind the panel clear the case and the module space (21.
  • XY6020L or DPS5005 display module · Or any panel module, using the custom cut-out sliders
  • USB-C PD trigger board, XT60 panel connector or 5.5 mm panel barrel jack · Choose with the Power input slider. Openings: USB-C 10.2 x 5 mm with a plug recess; XT60 16.2 x 8.8 mm; barrel jack 8.3 mm hole.
  • 4 × Stick-on rubber feet · Recommended: they stop the light case sliding when you plug in or pull leads

Assembly

  1. Print the fit frame. Push your module into the three openings (1, 2 and 3 dots = chosen clearance +0, +0.2, +0.4 mm). If only the 2- or 3-dot opening fits well, raise the Cut-out clearance slider by 0.2 or 0.4 mm before printing the case.
  2. Measure how deep your module sits behind the panel, including any heatsink, fan or wiring. If it is more than 27 mm (XY6020L) or 38 mm (DPS5005) plus the 15 mm spare, raise the Spare depth slider.
  3. Press 4 M3 heat-set inserts into the cover: the two rear corner blocks under the roof and the two bosses at the bottom of the front panel.
  4. USB-C version: slide the trigger board along the two grooved rails on the base until its socket sits against the inside of the back wall behind the opening.
  5. Snap the display module into the front panel from the outside. Fit the binding posts with their nuts behind the panel, red on the left, black on the right, then wire the input, module and posts.
  6. Lower the cover straight down over the base. Fit 2 M3 x 8 countersunk screws through the back wall and 2 up through the floor.
  7. Stick 4 rubber feet under the base.

Good to know

  • DC input only: a USB-C PD trigger, an XT60 battery lead or a barrel-jack adapter. There is no mains wiring inside, and this case is not designed for any.
  • With the default USB-C PD input, the output can't exceed what your charger negotiates (USB PD chargers top out at 100 W, or 240 W with newer EPR chargers and triggers). That is far below what these modules are rated for. If you need more power, choose the XT60 or barrel input and a suitable DC suppl
  • Module sizes: XY6020L 79 x 43 x 27 mm with a 71.3 x 39 mm cut-out (manuals.plus listing for the XY6020L); DPS5005 cut-out 71 x 39 mm, 38 mm deep (Joy-IT DPS5005 manual). Sellers and clones differ. The case keeps 15 mm of spare depth behind the module by default; measure yours and raise the Spare dep
  • The engine checks fit and clearance, not temperature. Keep the roof vents clear. Nothing here proves your converter stays cool at full load, so watch its temperature on the first long run.
  • The front panel is 2.4 mm thick. The engine does not check whether your module's side clips grip a 2.4 mm panel; the fit frame is the same thickness, so try that first.
  • The converter-board bay (off by default) is a generic space for a separate board you supply. The engine checks its clearance only when you switch it on, and its standoffs sit 4 mm in from each corner of the bay size you set; match them to your board's holes or drill the floor.
  • The trigger-board rails fit boards 12 to 30 mm wide with the USB-C socket at the edge. If the board slides loose, add a drop of hot glue at the front of the rails.
  • The XT60 opening is cut for the connector housing; use a panel-mount XT60 or glue the connector in.
  • The empty case is light: it tips at about 1.4 N pulled sideways at the posts. The module adds weight, and rubber feet help it stay put, but a hard yank on the leads will move it.

Comments