From the Loftsmith Workshop
Mini fireplace case for Cheap Yellow Display (CYD) ESP32
Turns a bare Cheap Yellow Display into a little hearth for your shelf. The screen sits in the opening, two panelled doors swing open at the front, and four small hooks along the mantel are ready for tiny stockings. Change the room behind the screen to suit your board.
6 parts · 106 g · 119 × 82 × 118 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- surround · PLA (stone colour) · Upright as it stands; prints together with door-left and door-right as one print-in-place object
About 29 g, 48 min. Fluted pilasters, splayed firebox opening, board slot, side USB windows, dovetail grooves underneath.
- door-left · PLA (stone colour) · Upright, standing open at 90 degrees on its hinge, same print as the surround
About 5 g. Paned door on a pinless cone hinge.
- door-right · PLA (stone colour) · Upright, standing open at 90 degrees on its hinge, same print as the surround
About 5 g. Not present when Doors is set to Single.
- mantel · PLA (walnut colour) · Upside down, shelf top on the bed
About 22 g, 35 min. Coved shelf with a rounded top edge, stocking hooks, and two tabs that close the board slot.
- chimney · PLA (stone colour) · Upright as it stands
About 17 g, 30 min. Tapered breast with rounded corners, a recessed panel, a flared cornice and a rounded cap.
- hearth · PLA (walnut colour) · Flat, dovetail rails up
About 27 g, 40 min. Board-grooved deck with a sunken panel under the door swing. Two rails lock the surround on.
Print settings
- Layer height
- 0.2 mm
- Walls
- 2
- Infill
- 15%
- Supports
- None
- Notes
- At the defaults the whole set is about 110 g and 3 h 11 min of PLA at 2 walls, 15% infill. At 3 walls and 15% it is about 140 g and 4 h 0 min. Four prints: the surround with both doors as one print-in-place object, the mantel upside down, the chimney upright, the hearth flat. Two colours: stone for
Hardware
- 2 × 1.75 mm filament offcut, 8 mm long · Locating pins between the mantel and the chimney breast.
- 2.8 in Cheap Yellow Display (ESP32-2432S028), 86 x 50 mm board · Not printed. Set the Screen thickness slider to your measured thickness, including the parts on the back.
- USB power lead · Plugs into the board edge through a side window and runs to the back.
Assembly
- Print the surround and doors as one object. When it is cool, swing each door gently closed and open a few times to free the cone hinges. If a door stays fused, reprint with a larger Hinge gap.
- Slide the surround onto the hearth from behind: line up the dovetail grooves under its floor with the two rails, then push forward until it stops.
- Lower the CYD into the slot from the top, screen facing out, so it rests on the slot floor behind the opening.
- Plug the USB lead into the board edge through one of the side windows and run it to the back.
- Push two 8 mm pieces of 1.75 mm filament into the holes on top of the mantel. Lower the mantel onto the surround so its two tabs drop into the board slot.
- Set the chimney breast onto the two filament pins.
- Play a looping fire video on the screen and open or close the doors.
Good to know
- Hinges, dovetail fit and board fit are checked in the Loftsmith engine only, not on a real print. If a door will not free, raise the Hinge gap slider (0.3 to 0.6 mm).
- Measure your board's thickness across the screen and the parts on its back, and set Screen thickness (10 to 20 mm). The slot is sized from that number.
- On many CYD boards the picture is not centred on the board. Measure how far the picture centre sits from the board centre and set Picture offset. The side USB windows assume the port is on a short edge of the board.
- Made for the 2.8 in CYD only. Other screens are not supported.
- The door panes are solid: 0.9 mm thin, but not see-through. Open the doors to see the fire.
- The stocking hooks are checked for 200 g each. Stockings hanging in front of the doors stop them from opening.
- PLA softens at about 55 degrees C. Keep it away from radiators and real fires.
Comments