From the Loftsmith Workshop

Geneva drive Christmas countdown dial, 8 to 31 days

A little desk dial that counts the days to Christmas. Turn the crank once each morning and the numbered wheel steps forward one place, stopping at the marker marked Days To Go. Pick how many days it counts and how big the dial is.

5 parts · 78 g · 174 × 152 × 44 mm

by Loftsmith Workshop

Red numbered wheel with a white star hub and a crank, on a green base reading Days To Go
Loading the 3D view
Loading the 3D view
No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Parts

  • base · PLA (green) · Flat on the bed, posts pointing up

    173.7 x 152.2 x 19 mm at the defaults. About 46 g and 66 min, including the colour changes for the trim. Carries the dial post, the crank post and an arrowhead pointer with a notched tail aimed at today's number.

  • base trim · PLA (cream, optional second colour) · Printed with the base, 1.2 mm raised

    Turn arrow and front label. With one filament it prints in the base colour and the lettering is still raised.

  • driver · PLA (red) · Upright, drum down, neck and pin pointing up

    About 3 g, 10 min. Holds the round locking neck, the 4.4 mm drive pin and the key that carries the crank.

  • dial · PLA (red) · Flat on the bed

    115.0 mm across the slot tips at the 115 mm default (114.6 mm square bounding box), with 24 slots. About 23 g, 34 min. Three spoke windows let the base show through.

  • numbers · PLA (cream, optional second colour) · Printed with the dial, 1.2 mm raised

    Digits count down clockwise from the day count. 5.8 mm tall at the defaults, never under 5 mm.

  • star cap · PLA (cream) · Flat, flat side down

    About 1 g, 5 min. Presses 2 mm deep onto the dial post tip and stops the dial lifting more than 0.6 mm.

  • crank · PLA (red) · Flat, handle pointing up

    About 5 g, 12 min. The fluted handle is one piece with the crank arm. Its key and pin hole slip over the driver.

Print settings

Layer height
0.2 mm
Walls
2 walls, or 3 if you want a stiffer pin and neck
Infill
15%. The 86 g and 2 h 24 min figures are for 2 walls and 15%; 3 walls at 15% is about 116 g and 3 h 12 min.
Supports
None. Print the driver upright with the drum down.
Notes
PLA, 0.4 mm nozzle. The moving fits are 0.25 mm per side between the pin and the dial slots, 0.4 mm between the locking neck and the dial scallops, and 0.15 mm in the crank's key and pin hole. If your printer runs tight, print a small test of a couple of slots first. For cream lettering, change colo

Assembly

  1. Print all the parts. If the first-layer edge on the driver drum or the dial's centre hole is rough, clean it with a craft knife.
  2. Press the driver, drum down, onto the 10 mm crank post on the right of the base until it sits on the boss. Turn it so the pin points away from the dial post.
  3. Lower the dial over the centre post so one scallop wraps the driver's round locking neck and the highest number sits at the arrowhead pointer. The pin stays outside the dial.
  4. Press the star cap onto the thin tip of the centre post. It sits 2 mm deep and leaves the dial 0.6 mm of lift; a drop of glue is optional.
  5. Slide the crank onto the driver so the key and pin hole seat on the shoulder, handle pointing away from the dial. Turn it clockwise, as the base arrow shows: one full turn moves the dial one number.
  6. To set the starting day, lift off the crank and star cap, raise the dial and drop it back with a different number at the pointer.

Good to know

  • Checked in the Loftsmith engine only; nobody has printed it. The running clearances (0.25 mm per side in the slots, 0.4 mm lock gap, 0.15 mm in the crank) may need tuning for your printer, and friction and wear are untested.
  • Strength figures are hand estimates against PLA's across-layer allowable of 5.0 MPa. At the defaults the neck and pin together see 1.8 MPa under a 10 N push and the pin sees 2.9 MPa under a 5 N turn. Don't force the dial round by hand or crank hard against a jam, because the 4.4 mm pin is the weakes
  • The dial diameter slider is the printed size across the slot tips, from 115 to 160 mm. It starts at 115 mm because a smaller dial can't fit the numbers for 31 days. At 31 days the digits are 5 mm tall with 1.2 mm between neighbours, so that is the most crowded layout.
  • The base grows with the dial and the crank. At the defaults it is 173.7 x 152.2 mm and fits a 180 mm bed. In the extreme builds it was 214.6 x 198.9 mm with a 160 mm dial and 24 mm crank, and 201.5 x 161.0 mm with 8 days and a 44 mm crank; those need a 220 mm or larger bed.
  • Contains small parts (a 20 mm star cap and the driver), so keep it away from young children. It is for decoration and desk use only.
  • It is not a clock: it only advances when someone turns the crank.

Comments